Welcome to Our Community

Some features disabled for guests. Register Today.

Blackbox, No toolhead connector, Relay for IOT?

Discussion in 'OpenBuilds Forum Help' started by Tarquynn, Jul 26, 2022.

  1. Tarquynn

    Tarquynn New
    Builder

    Joined:
    Mar 27, 2019
    Messages:
    8
    Likes Received:
    0
    First post. I finished my Lead 1515 build, got everything running smooth, and built up a small dust collection system. I got an IOT relay, but can't connect it per the instructional video. My blackbox did not come with a 4-pin toolhead connector (see attached images), but DID come with a 2-pin Relay connector (again, see images).
    Can I connect the IOT relay to the 2-pin Relay on the blackbox?
    If so, what Gcode commands would activate it?
    Thanks in advance.
     

    Attached Files:

  2. Alex Chambers

    Alex Chambers Master
    Moderator Builder

    Joined:
    Nov 1, 2018
    Messages:
    2,791
    Likes Received:
    1,369
    If that is a picture of your blackbox it does have a toolhead connector, or do you mean it doesn't have the four pin connector to plug into it?
    Alex.
     
  3. Giarc

    Giarc OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jan 24, 2015
    Messages:
    3,021
    Likes Received:
    1,689
    Here is how you connect the IOT to the blackbox. docs:blackbox:connect-dewalt-iotrelay [OpenBuilds Documentation] Technically, you should be able to use the 2 pin if you look at the wiring diagram in the link.
     
  4. Tarquynn

    Tarquynn New
    Builder

    Joined:
    Mar 27, 2019
    Messages:
    8
    Likes Received:
    0
    Doesn't have the 4 pin connector.
     
  5. Giarc

    Giarc OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jan 24, 2015
    Messages:
    3,021
    Likes Received:
    1,689

    You should be able to use the two. You need PWM and Ground and they are conveniently right next to each other. Just be ABSOLUTELY sure you put the right wires in the right spot so you do not damage the BlackBox. From the link I posted above:

    [​IMG]
     
  6. Tarquynn

    Tarquynn New
    Builder

    Joined:
    Mar 27, 2019
    Messages:
    8
    Likes Received:
    0
    So set the jumper as shown below and use w M3 & M5?

    Also - How do I access the jumpers? Just unscrew the cover?


    upload_2022-7-26_20-10-26.png
     
  7. Tarquynn

    Tarquynn New
    Builder

    Joined:
    Mar 27, 2019
    Messages:
    8
    Likes Received:
    0
    Popped off the cover, relay's already in the position above. I'll give it go and see what happens.
     
  8. Tarquynn

    Tarquynn New
    Builder

    Joined:
    Mar 27, 2019
    Messages:
    8
    Likes Received:
    0
    Tried it, and nothing. Troubleshooting that all yielded nothing:

    1. Jumper completely off.
    2. Jumper on M3/M5, wires "normal" (left to left, right to right)
    3. Jumper on M3/M5, wire reversed
    4. Jumper on M8/M9, wires "normal" (left to left, right to right)
    5. Jumper on M8/M9, wires reversed
    6. Changed wire, repeated 1-5, nothing

    I can hear the relay in the BB click when the appropriate command is sent, but it doesn't change the state of the IOT power supply.
    I'm out of ideas.
     
  9. Tarquynn

    Tarquynn New
    Builder

    Joined:
    Mar 27, 2019
    Messages:
    8
    Likes Received:
    0
    I did check one more thing, voltage across the relay connector & each leg to ground. Zero volts regardless of position.

    Should there be a voltage if either open or closed?
     
  10. Rick 2.0

    Rick 2.0 OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Dec 20, 2013
    Messages:
    2,896
    Likes Received:
    1,555
    My guess would be:

    upload_2022-7-26_20-47-14.png

    But again, that's just a guess.
     
  11. Tarquynn

    Tarquynn New
    Builder

    Joined:
    Mar 27, 2019
    Messages:
    8
    Likes Received:
    0
    Thanks for the reply, but that was #1 on the troubleshooting list.
     
  12. sharmstr

    sharmstr OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 23, 2018
    Messages:
    2,059
    Likes Received:
    1,449
    No need to move everything around and try a bunch of combos. Just wire it as shown in the docs. You should get around 5V on the grnd to pwm connection. If not, you may need to open a support ticket. Support

    And I have to mention the following since it happens often....
    Make sure the router is plugged into one of the normally OFF sockets. Make sure the router switch is in the on position.
     
  13. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    15,127
    Likes Received:
    4,329
    Wire it exactly as shown in docs:blackbox:connect-dewalt-iotrelay [OpenBuilds Documentation]
    As mentioned above as well, please don't try random other wiring setups just because - if its not documented, it's not the right way. If your wiring experiments damage your BlackBox your warranty will not cover your mistakes: See OpenBuilds Warranty and note:

    If you accidentally misplaced the Plug, you can order additional connectors from Xtension Connector Sets
    If it truly was missing from your order, contact the Store you purchased it from and alert them that there were missing items so they can resolve it for you.
     
    Mark Carew and David the swarfer like this.
  14. Tarquynn

    Tarquynn New
    Builder

    Joined:
    Mar 27, 2019
    Messages:
    8
    Likes Received:
    0
    I messaged the Openbuilds shop about the missing connectors, waiting on a reply. Is it documented anywhere that they're supposed to be supplied with the Blackbox? If so, I didn't see it.
     
  15. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    15,127
    Likes Received:
    4,329
  16. Giarc

    Giarc OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jan 24, 2015
    Messages:
    3,021
    Likes Received:
    1,689
    I did nothing to the jumpers. There is nothing that I could see in the instructions I linked that mentions doing anything to the jumper. The 1 minute and 30 second long video shows everything you need to do.
     

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice