Welcome to Our Community

Some features disabled for guests. Register Today.

Help needed with breakout board

Discussion in 'CNC Mills/Routers' started by Saint Billy, Jan 29, 2017.

  1. Saint Billy

    Builder

    Joined:
    Dec 1, 2016
    Messages:
    74
    Likes Received:
    8
    I have recently purchased an HG08 breakout board which connects to a U300 motion controller to run my newly built Ox cnc.

    I am a woodworker and a little embarrased as my electrical knowledge is pathetic compared to a lot of you on here, hence my asking for help.

    The HG08 breakout board supports 5 axis, I have 4 nema stepper motors to connect to the board each of which has 4 wires, red, green, yellow, blue. On the breakout board each stepper motor input has GND, VCC, CKA-D, CWC, ENA-D.

    Breakout board HG08.jpg
    I do not have a clue what wire does what on the stepper motor nor do I know what goes to where on the breakout board. I know you can connect a voltage meter to the stepper motor or connect and pair stepper motor wires to check resistance but that still does not help me detemine where each wire goes as I do not understand CKA etc abbreviations on the breakout board.

    If someone knows what wire goes to what that would be a massive help.

    Also, on the controller boards I have seen there is a clone drive for the second Y axis stepper, presumerably on this it just goes into one of the spare A or B inputs as there is no clone?.

    Cheers in advance.
     
  2. Kevon Ritter

    Kevon Ritter Veteran
    Builder

    Joined:
    Apr 30, 2015
    Messages:
    597
    Likes Received:
    294
    A breakout board serves are a means of communication between your computer and your machine. A breakout sends signals to a separate unit called a driver. The driver is what controls the stepper. Each stepper has its own driver.
     
    Saint Billy likes this.
  3. Giarc

    Giarc OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jan 24, 2015
    Messages:
    3,022
    Likes Received:
    1,690
    You also need to figure out which wire is paired with which. Pick a wire. Hold one of the other three to that wire. Try to turn the motor. If it is extremely hard to turn, that is a pair. If not, pick another wire. The Ox build videos go through many of the intricacies of building a CNC to include finding wire pairs. If your motor turns the wrong way, pick one wire pair and reverse their hook-ups to the board.
     
    Saint Billy likes this.
  4. Saint Billy

    Builder

    Joined:
    Dec 1, 2016
    Messages:
    74
    Likes Received:
    8
    Well that clears that up, I have obviously overlooked that another bit of kit is needed, in fact 4 bits of kit, oh dear. Thanks for the spot Kevon.

    So what exactly is the advantage of having a setup that has a Motion control board, Breakout board and drivers verses something like the Xpro3 where everything is on one board?.
     
  5. Saint Billy

    Builder

    Joined:
    Dec 1, 2016
    Messages:
    74
    Likes Received:
    8
    Thanks Giarc,

    I am out of my comfort zone with electrics as you can tell and have spent so long building the Cnc that I have mentally hit the wall, and it now looks like I need additional bits but hey ho. I will take your advice thanks for the help.
     
  6. Darathy

    Darathy New
    Builder

    Joined:
    Jul 12, 2016
    Messages:
    74
    Likes Received:
    21
    Benefit is drivers(depends which you get) can power a more powerfull stepper motors compared to xpro and they might even run them smoother.
     
    Saint Billy likes this.
  7. Saint Billy

    Builder

    Joined:
    Dec 1, 2016
    Messages:
    74
    Likes Received:
    8
    Ahh ok, that makes sense, thanks.
     
  8. Rick 2.0

    Rick 2.0 OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Dec 20, 2013
    Messages:
    2,898
    Likes Received:
    1,556
    ...and if you burn out a stand alone driver it's no big deal to replace. Not quite the case with built-in drivers.
     
    Saint Billy likes this.
  9. Saint Billy

    Builder

    Joined:
    Dec 1, 2016
    Messages:
    74
    Likes Received:
    8
    Good point Rick 2.0
     

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice