Welcome to Our Community

Some features disabled for guests. Register Today.

Miter Saw Stop Block

Discussion in 'Other Builds' started by rkugler, Feb 14, 2018.

  1. rkugler

    rkugler New
    Builder

    Joined:
    Sep 1, 2016
    Messages:
    3
    Likes Received:
    12
    rkugler published a new build:

    Read more about this build...
     
  2. JustinTime

    JustinTime Veteran
    Builder

    Joined:
    Dec 18, 2013
    Messages:
    784
    Likes Received:
    259
    The way I see it you will need to zero the stop every time you turn on the machine since it will not know where it is. If the machine is on all day it's not a big problem since it has to be zeroed only once a day.
    You will need a positive lock on the stop or it will move every time you bump against it. While the motors are powerful and should resist moving while under power it still may move a fraction.
     
  3. rkugler

    rkugler New
    Builder

    Joined:
    Sep 1, 2016
    Messages:
    3
    Likes Received:
    12
    Hi Justin,
    Ohhhh, good point about zeroing. Could there be a shut down procedure where the stop goes 'home' upon power down, then knows where it is at start up? Hadn't considered having to lock the stop..... but I see how it could be bumped out. Is there a way to lock a belt drive like a shaft lock on a screw?

    All good points, thanks so much!
    Roger
     
  4. JustinTime

    JustinTime Veteran
    Builder

    Joined:
    Dec 18, 2013
    Messages:
    784
    Likes Received:
    259
    The belt can not be locked in any meaningful way. One way to solve the locking is to use a thin threaded rod, like #6x32. It has teeth every 1/32". Run it the whole length of the side. Have a small #6 rod, maybe 1", engage into the long run when you have reached the stop position. It will have to be done with a servo or with an electromagnet and spring. You'll have to write the code for it to engage and disengage when needed.
     
  5. rkugler

    rkugler New
    Builder

    Joined:
    Sep 1, 2016
    Messages:
    3
    Likes Received:
    12
    Ya, that would work. The miter stop I'm using now uses this technique. OK, lots to think about. Thanks!
     
  6. R. D. Childers

    Builder

    Joined:
    Dec 8, 2016
    Messages:
    8
    Likes Received:
    0
    What is the status of this project?
     
    #6 R. D. Childers, Apr 21, 2019
    Last edited: Jun 26, 2020
  7. pauna

    pauna New
    Builder

    Joined:
    May 18, 2016
    Messages:
    54
    Likes Received:
    13
    You continue your project "Mit Saw Stop Block"

    I also want to get closer to doing something like "Table Saw Fence Control"

    I find programming difficult

     
    Mark Carew likes this.
  8. Rick 2.0

    Rick 2.0 OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Dec 20, 2013
    Messages:
    2,896
    Likes Received:
    1,555
    You might take a look at this project: Cut To Length Machine
     
  9. pauna

    pauna New
    Builder

    Joined:
    May 18, 2016
    Messages:
    54
    Likes Received:
    13
    thanks. Maybe the discussion will resume there as well
     

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice