Welcome to Our Community

Some features disabled for guests. Register Today.

Recommend a good 3D extrusion head...

Discussion in 'Suggestions' started by Jon Cherba, Sep 3, 2014.

  1. Jon Cherba

    Builder

    Joined:
    Sep 3, 2014
    Messages:
    18
    Likes Received:
    0
    I want to design a 3D printer for my final project of my drafting degree. I'm not sure what print head or where to really look for one. I want accuracy and reliability in the extrusion head. thanks for your time.
     
  2. dddman

    dddman Journeyman
    Builder

    Joined:
    Mar 2, 2014
    Messages:
    468
    Likes Received:
    187
  3. Jon Cherba

    Builder

    Joined:
    Sep 3, 2014
    Messages:
    18
    Likes Received:
    0
    I looked at both of those links and I really like the e3d-V6. I should be satisfied with that for a long while given all it can print. Do I need to find or design a feeder for this too or should I just buy one already built?
     
  4. dddman

    dddman Journeyman
    Builder

    Joined:
    Mar 2, 2014
    Messages:
    468
    Likes Received:
    187
    I would say to print one by yourself... You'll have to find someone that can print it for you I think ;) What will be your printer? There are some design available on www.thingiverse.com
     
  5. Mark Carew

    Mark Carew OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jun 28, 2013
    Messages:
    2,759
    Likes Received:
    2,443
  6. Jon Cherba

    Builder

    Joined:
    Sep 3, 2014
    Messages:
    18
    Likes Received:
    0
    Which version of the E3D V6 would you recommend for the most versatility and accuracy? I was thinking the 1.75mm universal would give me the broadest material printing options.
     
  7. bobt

    bobt Well-Known
    Builder

    Joined:
    Dec 4, 2013
    Messages:
    89
    Likes Received:
    38
    I purchased a E3D V5 and then bought the parts necessary to upgrade to a V6. Love the head. Also buy several tips for the printer because it makes it easier to change the tip if it gets jammed buy less than quality filament. It can happen I know. It was not a deal that I thought it was. It was a simple matter to remove and replace the tip which allowed me to clean out the head. If you want to purchase the print head that is based upon a "Greg's Hinged Accessible Extruder" you can find it here: http://www.makerfarm.com/index.php/3d-printer-kits/greg-s-hinged-accessible-extruder.html
    I don't own the company or work for them just a satisfied customer.
    I have a build here that uses that specific extruder here: http://www.openbuilds.com/builds/bobs-3d-printer-kit-build.651/

    Bob
     
  8. Jon Cherba

    Builder

    Joined:
    Sep 3, 2014
    Messages:
    18
    Likes Received:
    0
    so now that I have decided to go with the e3d v6...Which version is recommended? 1.75mm or 3mm? Direct or Bowden? I don't know which one to choose...I have an idea what does what but not 100%...I'm thinking about doing a dual extruder as well...
     
  9. Jon Cherba

    Builder

    Joined:
    Sep 3, 2014
    Messages:
    18
    Likes Received:
    0
    Or I may go with a single extruder to lower building cost and lessen complication...
     
  10. dddman

    dddman Journeyman
    Builder

    Joined:
    Mar 2, 2014
    Messages:
    468
    Likes Received:
    187
    1.75mm direct for sure! I had a dual extruder and never used it. Most of the time I just don't care what color are my projects.
     
  11. Jon Cherba

    Builder

    Joined:
    Sep 3, 2014
    Messages:
    18
    Likes Received:
    0
    It's not the color that I would be mainly using it for it would be either dual material or print with support material. like phone case that's soft / flexible around the phone then hard / rigid on the outside as an example...

    Why do you recommend the 1.75mm over the 3mm anyways? I'm curious because I really want to learn as much as possible about 3D printers and how they work. I'm building this for a final project for my drafting degree. I also love to design things and would love to be able to build them quickly and efficiently.

    Direct - right on top of the hot end - correct?
    Bowden - remote filament feeding / from a distance like closer to the spool- correct?

    What are the advantages and disadvantages?
     
  12. Jon Cherba

    Builder

    Joined:
    Sep 3, 2014
    Messages:
    18
    Likes Received:
    0
    I would love to be able to print Carbon Fiber and Kevlar like these guys... https://markforged.com/ ...that filament is high dollar...
     

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice