Welcome to Our Community

Some features disabled for guests. Register Today.

Sign Up

blackbox controller

Discussion in 'General Talk' started by cpu999-1, Aug 16, 2020.

  1. cpu999-1

    cpu999-1 New
    Builder

    Joined:
    Feb 25, 2020
    Messages:
    28
    Likes Received:
    1
    my openbuilds blackbox controller keeps losing its signal why ?
     
    #1 cpu999-1, Aug 16, 2020
  2. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    15,262
    Likes Received:
    4,357
    #2 Peter Van Der Walt, Aug 16, 2020
  3. cpu999-1

    cpu999-1 New
    Builder

    Joined:
    Feb 25, 2020
    Messages:
    28
    Likes Received:
    1
    so are you saying need to buy shielded wire ?
     
    #3 cpu999-1, Aug 20, 2020
  4. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    15,262
    Likes Received:
    4,357
    Not really. Refer to the link above. There are several things to try before resorting to shielded wiring. For example shorter USB cable and spacing low voltage cabling away from EMI sources
     
    #4 Peter Van Der Walt, Aug 21, 2020
  5. cpu999-1

    cpu999-1 New
    Builder

    Joined:
    Feb 25, 2020
    Messages:
    28
    Likes Received:
    1
    so are limit switches low voltage ?? and if they are keep them away from the motor cables
     
    #5 cpu999-1, Aug 21, 2020
  6. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    15,262
    Likes Received:
    4,357
    Yes, limits are very sensitive low voltage logic signals.
     
    #6 Peter Van Der Walt, Aug 22, 2020
  7. cpu999-1

    cpu999-1 New
    Builder

    Joined:
    Feb 25, 2020
    Messages:
    28
    Likes Received:
    1
    ok what I did is use shorter usb cable and routed the wires away from each other seems to work just fine thanz 4 the help,plus the usb cable is a ink printer cable,now about stepper motor adjustment is the b/b pre set,or do I ajust them, if so how do I DO that ?BECAUSE SOME TIMES i SEE THE RED LIGHTS COME ON
     
    #7 cpu999-1, Aug 25, 2020
  8. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    15,262
    Likes Received:
    4,357
    Default is good for most machines.
    Are you skipping steps, turn it up a bit. Overheating drivers (red LED) or overheating motors (burns your hand) turn it down a bit

    All explained here: docs:blackbox:currentadjustment [OpenBuilds Documentation]

    Note red LED could be overheating, but not limited to it:

     
    #8 Peter Van Der Walt, Aug 25, 2020
  9. cpu999-1

    cpu999-1 New
    Builder

    Joined:
    Feb 25, 2020
    Messages:
    28
    Likes Received:
    1
    no step skipping,the motors are warm to the touch,but if there not working there warm,but where I live its gets over a hundred some times,so do I need to setup a volt meter to adjust them ?
     
    #9 cpu999-1, Aug 25, 2020
    Last edited: Aug 25, 2020
  10. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    15,262
    Likes Received:
    4,357
    Sounds good to me. Warm motors is normal. Burning hot is not. Warm when not working is normal too (brake condition, both coils enegised to maintain position)
     
    #10 Peter Van Der Walt, Aug 25, 2020
  11. cpu999-1

    cpu999-1 New
    Builder

    Joined:
    Feb 25, 2020
    Messages:
    28
    Likes Received:
    1
    ok thanz 4 all your help
     
    #11 cpu999-1, Aug 26, 2020
    Peter Van Der Walt likes this.

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice