Welcome to Our Community

Some features disabled for guests. Register Today.

Controller for XYYZA

Discussion in 'CNC Mills/Routers' started by Allistar, Feb 5, 2021.

  1. Allistar

    Allistar New
    Builder

    Joined:
    Aug 19, 2019
    Messages:
    57
    Likes Received:
    19
    Hi all,
    Can anyone recommend a controller that's GRBL compatible that can drive a LEAD1515 (with two Y steppers) with a rotary stepper as well? The controllers I've seen (BlackBox or XPro V5) can only control 4 steppers.

    Thanks,
    Allistar
     
  2. Giarc

    Giarc OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jan 24, 2015
    Messages:
    3,008
    Likes Received:
    1,676
    GRBL can not run four different axis at once. So if you want a rotary, you disconnect either the X or Y and use that driver to operate the rotary. This was the primary reason I built a stand alone CNC lathe. It is not difficult to do, you just need to change your steps/mm each time you switch. I would run it along the Y axis so only the X would need to be disconnected and the rotary axis could be longer.
     
  3. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    14,927
    Likes Received:
    4,291
    You swop the rotary into X or Y, and use Wrapping (video below)


    Super easy to connect/disconnect thanks to Xtension Connectors
     
    Giarc likes this.
  4. Rob Taylor

    Rob Taylor Master
    Builder

    Joined:
    Dec 15, 2013
    Messages:
    1,470
    Likes Received:
    748
    Look into grblHAL and grbl_Esp32. Once you graduate past three basic axes, there's a lot less hand-holding and you'll have to work on your own electronics hardware. Luckily, doesn't seem particularly difficult with either of those. bCNC seems to have become a dedicated grblHAL sender, which is interesting. Getting 4-axis jobs out of CAM is another matter, though, that's the big thing to look into.
     
  5. Allistar

    Allistar New
    Builder

    Joined:
    Aug 19, 2019
    Messages:
    57
    Likes Received:
    19
    Thanks, that's helpful. I'll use the driver of the X stepper to control the rotary. When I build it I'll get an extra stepper motor cable so changing it is easy.
     
    Giarc and Peter Van Der Walt like this.
  6. JustinTime

    JustinTime Veteran
    Builder

    Joined:
    Dec 18, 2013
    Messages:
    780
    Likes Received:
    257
    I use GRBL on my machine. I have two Y axis steppers. I have both drivers connected to the same Step and Direction pins on the Nano3. It works for me with no problems.

    Edit: Just dawned on me that you are talking about an integrated system where as I use separate drivers and Nano3. This handicap of GRBL made me go with the separate system in the first place.
     
    #6 JustinTime, Feb 6, 2021
    Last edited: Feb 6, 2021
  7. Allistar

    Allistar New
    Builder

    Joined:
    Aug 19, 2019
    Messages:
    57
    Likes Received:
    19
    Thanks for the replies. The only reason I'm suggesting GRBL is because that seems to be the default for the OpenBuilds hardware and the XPRO V5. I can build my own drivers to control 5 steppers at once (my current CNC uses HobbyCNC drivers and LinuxCNC). For the low number of times I'll use a rotary axis I'll stick with 4 drivers and I'll switch the stepper's plug manually (and change the appropriate config).
     
    Peter Van Der Walt likes this.

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice