Hello. I have a problem with the laser. while engraving, the laser does not move smoothly and stops for a second. Does anyone have any idea what kaman is about? is it a question of settings? I attach a photo with dots. To sum up: the laser goes as normal, stops for a moment and continues on. I have no idea where to start.
Post your Grbl settings please. CONTROL > grbl settings tab > Backup Grbl Settings (lets make sure advanced motion settings weren't changed) Also make sure your GCODE uses M4 Dynamic power: Grbl v1.1 Laser Mode · gnea/grbl Wiki
"Also make sure your GCODE uses M4 Dynamic power: Grbl v1.1 Laser Mode · gnea/grbl Wiki" - How can I change it? start? Could you instruct me?
Tip: The Backup Grbl Settings button on the toolbar of that window makes for an easier to read and access text file
[QUOTE = "Peter Van Der Walt, post: 121222, członek: 69967"]Wskazówka: Przycisk Backup Grbl Settings na pasku narzędzi tego okna ułatwia czytanie i dostęp do pliku tekstowego [/QUOTE] 0=10 zł; Czas impulsu krokowego, mikrosekundy $1=255 ; Opóźnienie biegu jałowego, milisekundy 2 dolary=0; Odwrócenie impulsu krokowego, maska 3$=0; Odwróć kierunek kroku, maska 4$=1; Pin włączania kroku odwrócenia, wartość logiczna 5$=0; Odwróć kołki ograniczające, wartości logiczne 6 USD=0; Odwróć pin sondy, wartość logiczna 10$=1; Opcje raportu o stanie, maska 11 USD = 0,020 ; Odchylenie złącza, milimetry 12 USD = 0,002 ; Tolerancja łuku, milimetry 13 USD = 0; Raport w calach, wartość logiczna 20 $ = 0 ; Włączenie limitów miękkich, wartość logiczna 21$=1; Włączenie twardych limitów, wartość logiczna 22 USD=1; Włączenie cyklu bazowania, wartość logiczna 23 USD = 0; Odwrócenie kierunku bazowania, maska 24 $ = 100 000 ; Szybkość posuwu lokalizacji bazowania, mm/min 25 $ = 2000.000 ; Szybkość wyszukiwania bazy danych, mm/min 26 USD = 250 ; Opóźnienie odbicia przełącznika bazowania, milisekundy 27 USD = 5.000 ; Odległość oderwania przełącznika bazowania, milimetry 30 $ = 1000 ; Maksymalna prędkość wrzeciona, RPM 31 $ = 0 ; Minimalna prędkość wrzeciona, RPM 32$=1; Włączenie trybu laserowego, wartość logiczna 100 $ = 200 000 ; Kroki osi X na milimetr 101 $ = 200 000 ; Kroki osi Y na milimetr 102 USD = 200 000 ; Kroki osi Z na milimetr 110$ = 3500.000 ; Maksymalna prędkość osi X, mm/min 1111 USD = 3500.000 ; Maksymalna prędkość osi Y, mm/min 112 USD = 3500.000 ; Maksymalna prędkość osi Z, mm/min 120 USD = 350 000 ; Przyspieszenie osi X, mm/s^2 121 USD = 350 000 ; Przyspieszenie w osi Y, mm/s^2 122 USD = 350 000 ; Przyspieszenie osi Z, mm/s^2 130$=1190.000 ; Maksymalny przesuw w osi X, milimetry 131 USD = 1300.000 ; Maksymalny skok w osi Y, milimetry 132$=97.000; Maksymalny przesuw osi Z, milimetry $I=leadmachine1515
0 = PLN 10; Step pulse time, microseconds $ 1 = 255; Idle delay, milliseconds $ 2 = 0; Step inversion, mask $ 3 = 0; Reverse step direction, mask $ 4 = 1; Reversal step enable pin, a boolean value $ 5 = 0; Reverse limiting pins, logical values $ 6 = 0; Reverse probe pin, a logical value $ 10 = 1; Status report options, mask $ 11 = 0.020; Joint deviation, millimeters USD 12 = 0.002; Arc tolerance, millimeters $ 13 = 0; Report in inches, logical value $ 20 = 0; Enable soft limits, Boolean $ 21 = 1; Enable hard limits, a logical value $ 22 = 1; Homing cycle activation, logical value $ 23 = 0; Homing direction reversal, mask $ 24 = 100,000; Homing location feed rate, mm / min $ 25 = 2,000,000; Database search speed, mm / min $ 26 = 250; Homing switch bounce delay, milliseconds 27 USD = 5,000; Homing switch tear-off distance, millimeters $ 30 = 1000; Maximum spindle speed, RPM $ 31 = 0; Minimum spindle speed, RPM $ 32 = 1; Turning on the laser mode, a logical value $ 100 = 200,000; X axis steps per millimeter $ 101 = 200,000; Y axis steps per millimeter $ 102 = 200,000; Z axis steps per millimeter $ 110 = 3,500,000; The maximum speed of the X axis, mm / min USD 1,111 = 3,500,000; The maximum speed of the Y axis, mm / min $ 112 = 3,500,000; The maximum speed of the Z axis, mm / min $ 120 = 350,000; Acceleration of the X axis, mm / s ^ 2 $ 121 = 350,000; Acceleration in the Y axis, mm / s ^ 2 $ 122 = 350,000; Z axis acceleration, mm / s ^ 2 $ 130 = 1,190,000; Maximum travel in the X axis, millimeters $ 131 = 1,300,000; Maximum stroke in the Y axis, millimeters $ 132 = 97,000; Maximum Z axis travel, millimeters $ I = leadmachine1515
I asked what CAM application you were using, right: To which you said: Thus my advice on how to set it up in OpenBuildsCAM. But now Your screenshot shows OpenBuildsCONTROL (Not OpenBuildsCAM) You are in the wrong application. Go to OpenBuilds CAM > Settings tab > Settings button Then setup Tool Initialisation:
No, that will cause the corners to burn. Please read: Grbl v1.1 Laser Mode · gnea/grbl Wiki as mentioned a lot earlier in this thread: If you have a spindle controlled by software, you have to come in here, remove the laser, add the spindle, when you are setting up routing jobs. Right tool settings for the job at hand