Welcome to Our Community

Some features disabled for guests. Register Today.

Lightburn open builds controller

Discussion in 'CNC Mills/Routers' started by Rommell1787, Dec 15, 2024.

Tags:
  1. Rommell1787

    Builder

    Joined:
    Nov 9, 2020
    Messages:
    30
    Likes Received:
    12
    Hi

    Anyone have issues using lightburn with a diode laser?

    i have issues wit jobs stopping half way through causing me to set and restart the controller. Very frsutrating. I use LB with my co2 laser and my dedicated diode engraver and have no issues.

    using my cnc for the larger bed size.

    Some photos of console and "busy" when the cnc stops the job.
     

    Attached Files:

  2. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    15,188
    Likes Received:
    4,346
  3. Rommell1787

    Builder

    Joined:
    Nov 9, 2020
    Messages:
    30
    Likes Received:
    12
    ill have a read.

    Works fine when i am using openbuilds software. No issues with stopping mid job or anything.

    Only happens when using LB
     
  4. Rommell1787

    Builder

    Joined:
    Nov 9, 2020
    Messages:
    30
    Likes Received:
    12
    Ive noticed after home cycle it goes into "busy" and needs a reset.

    Doesnt do this with open builds.
     

    Attached Files:

  5. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    15,188
    Likes Received:
    4,346
    Thats good, if so might be a lightburn bug, check in with their support
     
  6. Rommell1787

    Builder

    Joined:
    Nov 9, 2020
    Messages:
    30
    Likes Received:
    12
    I have posted in thier forum also but arent as responsive as you.

    the jobs do seem to stop at the same point each time ive tried. I have the black box V1.
     

    Attached Files:

  7. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    15,188
    Likes Received:
    4,346
    Try OpenBuilds CAM as a comparison, if it works with our CAM (Laser toolpaths are available in there) it rules out controller/GrblSettings etc
     
  8. Rommell1787

    Builder

    Joined:
    Nov 9, 2020
    Messages:
    30
    Likes Received:
    12
    No suprise, it works fine using open builds cam.

    Vid of issue in LB

     
  9. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    15,188
    Likes Received:
    4,346
    Did you setup lightburn per docs:software:lightburn [OpenBuilds Documentation] (just ruling it out)

    Console log there looks fine, got to PGM End no abnormal early stop

    Is your CAD file clean (not missing a segment? proper closed polylines etc)
    Betting if you export the gcode and run it with CONTROL it will miss that segment too (toolpath not sending issue)
     
  10. Rommell1787

    Builder

    Joined:
    Nov 9, 2020
    Messages:
    30
    Likes Received:
    12
    Im more concerned that the machine goes into "busy" even after homing. It doesnt respond to movement unless i reset the device and do not home after.

    I didnt follow that guide but the settings are the same anyway.

    The cad file is fine, i exported the dxf and used it in open builds cam. Again the machine doesnt respond after homing.
     
    #10 Rommell1787, Dec 16, 2024
    Last edited: Dec 16, 2024
  11. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    15,188
    Likes Received:
    4,346
    But fine in CONTROL right? Does it HOME in CONTROL?

    2 axes machine? $44/45 set correctly?
     
  12. Rommell1787

    Builder

    Joined:
    Nov 9, 2020
    Messages:
    30
    Likes Received:
    12
    Workbee cnc. attached backup of config
     

    Attached Files:

  13. Rommell1787

    Builder

    Joined:
    Nov 9, 2020
    Messages:
    30
    Likes Received:
    12
    Quick update.

    The LightBurn team have had me trying absolutely everything and they are struggling. I can generate gcode in Lightbrun and use CONTROL to run it and it works fine.

    I even tried anoher laptop and the same issue happens. Can the GRBL firmware be updated on the Black Box V1?
     
  14. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    15,188
    Likes Received:
    4,346
    Hasn't been any new Grbl releases since 2019 so nothing newer to update to

    Proving that Grbl and a well implemented Grbl compatible host works fine. So issue somewhere in LightBURNs comms code even if they won't admit it.

    Best solution for now then to use CONTROL as the host.
     
    David the swarfer likes this.
  15. Rommell1787

    Builder

    Joined:
    Nov 9, 2020
    Messages:
    30
    Likes Received:
    12
    Ive let the LB guys know about the firmware. for info i am using a block box V1 controller.
     

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice