Welcome to Our Community

Some features disabled for guests. Register Today.

Estlcam Controller

Discussion in 'CNC Mills/Routers' started by Keith Hicks, Nov 22, 2017.

  1. Keith Hicks

    Builder

    Joined:
    Nov 15, 2017
    Messages:
    3
    Likes Received:
    0
    Does anyone know of a GRBL Controller that is EstlCam ready and can handle nema 23s? I have an MPCNC with nema17s and a Arduino/Mega with Estlcam installed and I love the ease of using Estlcam to run it. But I'm starting a shopping list for a new Ox build and I would like to keep Estlcam as the GRBL controller software.
     
  2. msaeger

    msaeger New
    Builder

    Joined:
    Sep 23, 2015
    Messages:
    32
    Likes Received:
    1
    I am also a MPCNC builder looking to build a new machine. Christian has on the estlcam website that it supports the CNC xPRO controller that openbuilds sells.

    Are you going to cut your plates on the MPCNC or buy them?
     
  3. Giarc

    Giarc OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jan 24, 2015
    Messages:
    3,017
    Likes Received:
    1,682
    Yes you can:
    upload_2017-11-26_13-0-53.png
     
    Kyo likes this.
  4. msaeger

    msaeger New
    Builder

    Joined:
    Sep 23, 2015
    Messages:
    32
    Likes Received:
    1

    What are you using for the electronics? I am still looking for what to use for mine.
     
  5. msaeger

    msaeger New
    Builder

    Joined:
    Sep 23, 2015
    Messages:
    32
    Likes Received:
    1
    Thanks for all the links. I am thinking I want to not have hard wired stuff but we will see how it really works out when I get going. I tend to just get it working and say I will make it better later but then just leave it :)
     
  6. Keith Hicks

    Builder

    Joined:
    Nov 15, 2017
    Messages:
    3
    Likes Received:
    0
    Story of my life. lol
     
  7. msaeger

    msaeger New
    Builder

    Joined:
    Sep 23, 2015
    Messages:
    32
    Likes Received:
    1

    Hey Retrosmith,

    Can you tell me how you are going to connect the drivers to the Arduino? Is there a shield you can use for this? I am mostly finding people using larger external drivers are using a break out board and mach3 but I am thinking I would like something with an Arduino running Estlcam.
     
    #7 msaeger, Nov 29, 2017
    Last edited: Nov 29, 2017
  8. msaeger

    msaeger New
    Builder

    Joined:
    Sep 23, 2015
    Messages:
    32
    Likes Received:
    1

    Thanks again.
     
  9. msaeger

    msaeger New
    Builder

    Joined:
    Sep 23, 2015
    Messages:
    32
    Likes Received:
    1
    Sounds like it should work to me but I don't know what I am doing. I already have a UNO and Estlcam and whatever drivers I get will work with something else so I wouldn't be out anything anyway. I am pretty far from needing this anyway the parts I ordered on the black friday sale just shipped.

    Hope I am not asking you too many questions but you seem to be doing what I am wanting to do controller wise.

    The Y axis is going to have 2 motors (on mine anyway) how do you connect the two motors? Do you using one driver for both and connect them in parallel? If you use two drivers you must connect them both to the same step and dir pins on the Arduino since there is only one for each axis?
     
  10. Giarc

    Giarc OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jan 24, 2015
    Messages:
    3,017
    Likes Received:
    1,682

    Here is how Kyo demonstrated it and it worked for me and my Arduino set-up with DQ542MA drivers and a screw shield (skip the Rasberry Pi part unless you are using that with the Arduino). C-Beam cnc Also, read this: Connecting Grbl · gnea/grbl Wiki · GitHub and this: Wiring Limit Switches · gnea/grbl Wiki · GitHub Personally, I would read the entire GRBL Wiki. I found it very informative.
     
  11. Keith Hicks

    Builder

    Joined:
    Nov 15, 2017
    Messages:
    3
    Likes Received:
    0
    I didn't consider hooking the drivers directly to arduino. I thought it would need a grbl shield of some sort. Thanks for the info guys. Opens up more possibilities for me. I was looking at vpro but wasn't liking the price. If I blow it up, that's a lot of cash to swallow
     

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice