Welcome to Our Community

Some features disabled for guests. Register Today.

Sign Up

Recent Content by Mel Ristau

  1. Mel Ristau
    Post

    leveling doesn't stay level

    Thanks guys! Will use your suggestions and update on my progress.
    Post by: Mel Ristau, Sep 30, 2015 in forum: CNC Mills/Routers
  2. Mel Ristau
    Thread

    leveling doesn't stay level

    Not sure where this problem is coming from... I have two 1/2" layers of MDF (1200x1200mm) that I have screwed together and leveled. I shellac the...
    Thread by: Mel Ristau, Sep 29, 2015, 5 replies, in forum: CNC Mills/Routers
  3. Mel Ristau
    Post

    constant re-homing between each job?

    Understand now. Thanks for pointers John!
    Post by: Mel Ristau, Sep 8, 2015 in forum: Controller Boards
  4. Mel Ristau
    Thread

    constant re-homing between each job?

    Have upgraded TinyG firmware but still unable to run a series of jobs without re-setting board, re-homing and re-G92ing. If I run a Vectric cut2d...
    Thread by: Mel Ristau, Sep 6, 2015, 3 replies, in forum: Controller Boards
  5. Mel Ristau
    Thread

    tinyG Homing Error

    Need help translating this error message: {"er":{"fb":435.10,"st":31,"msg":"st_prep_line() move time is NAN"}} prep_null encountered thanks!
    Thread by: Mel Ristau, Dec 22, 2014, 1 replies, in forum: Controller Boards
  6. Mel Ristau
    Post

    Atypical Homing Setup

    Thanks David - just the kind of advice I'm looking for.
    Post by: Mel Ristau, Dec 21, 2014 in forum: CNC Mills/Routers
  7. Mel Ristau
    Post

    Atypical Homing Setup

    "What kind of switches?" Micro switches from Inventables wired NC. "Are you using the Github wiki?" Yes that's my primary guide.... Have about...
    Post by: Mel Ristau, Dec 20, 2014 in forum: CNC Mills/Routers
  8. Mel Ristau
    Post

    Atypical Homing Setup

    So here's a working solution: [ATTACH] But I still don't understand why it works.
    Post by: Mel Ristau, Dec 19, 2014 in forum: CNC Mills/Routers
  9. Mel Ristau
    Post

    Atypical Homing Setup

    Thanks Hytech2k!
    Post by: Mel Ristau, Dec 19, 2014 in forum: CNC Mills/Routers
  10. Mel Ristau
    Thread

    Atypical Homing Setup

    [ATTACH] The attached drawing shows that my switches are mounted on the gantry / not the rails. In brief, I'm wanting home to be at left back...
    Thread by: Mel Ristau, Dec 18, 2014, 12 replies, in forum: CNC Mills/Routers
  11. Mel Ristau
    Thread

    Cat5e cable?

    is this cable suitable for running NEMA 23 262oz-in motors at 24v? Since its 8 conductor, maybe using 4 pairs?
    Thread by: Mel Ristau, Nov 27, 2014, 3 replies, in forum: CNC Mills/Routers
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice