Welcome to Our Community

Some features disabled for guests. Register Today.

Sign Up

Swing Arm

Discussion in 'Other Builds' started by OpenBuilds, Dec 9, 2020.

Swing Arm

Swing Arm

Discussion in 'Other Builds' started by OpenBuilds, Dec 9, 2020.

Simple Swing Arm Build for the Modular Table Series. Create a simple vacuum swing arm that swings over your machine keeping your vacuum hose and router cord, etc. up and out of the way

swing arm vac vacuum wire management tables router
  1. OpenBuilds

    OpenBuilds Well-Known
    Staff Member Moderator Builder Resident Builder

    Joined:
    Sep 23, 2019
    Messages:
    22
    Likes Received:
    110
    OpenBuilds published a new build:

    Read more about this build...
     
    #1 OpenBuilds, Dec 9, 2020
    Rhett E likes this.
  2. Rhett E

    Rhett E Well-Known
    Builder

    Joined:
    Aug 3, 2020
    Messages:
    113
    Likes Received:
    45
    Thank you for making this video and post. Where did you source the 2.5" black hose? All I can seem to find is the clear stuff from Amazon. I've found something similar to yours from Woodriver but yours seems more stiff.

    Thanks again,
    Rhett E.
     
    #2 Rhett E, Dec 9, 2020
  3. Mark Carew

    Mark Carew OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jun 28, 2013
    Messages:
    2,758
    Likes Received:
    2,440
    Hello @Rhett E
    I joined a couple of my shop vacs hoses to make up 14' or so feet that I needed but you should be able to use something like this one
    2 1/2" Shop Hose
    Its a 20' and having the little extra may be nice for when you finish up a cut you can pull it off of the dust shoe and clean up any areas that the machine may have missed.
    Thank you for the kind words, your more then welcome I am glad to see its helping.
     
    #3 Mark Carew, Dec 10, 2020
    Rhett E and sharmstr like this.
  4. JustinTime

    JustinTime Veteran
    Builder

    Joined:
    Dec 18, 2013
    Messages:
    784
    Likes Received:
    259
    What Mark said or you could get it from HomeDepot for less.
     
    #4 JustinTime, Dec 10, 2020
    Mark Carew, Giarc, Rick 2.0 and 1 other person like this.
  5. Giarc

    Giarc OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jan 24, 2015
    Messages:
    3,015
    Likes Received:
    1,680
    And if you buy that top for a five gallon pail that showed up in JustinTime's link and put it between, you get a great cyclone that saves your filter in the shop vac.
     
    #5 Giarc, Dec 10, 2020
    Evilspawn and Mark Carew like this.
  6. WilliamK

    WilliamK New
    Builder

    Joined:
    Dec 14, 2021
    Messages:
    3
    Likes Received:
    4
    Very well done. Only change I had to make was the size of the hole drilled into the table top. In this area of the country, 1/2" EMT conduit has an OD of 0.705" or so. A 3/4" diameter drill gave just a little clearance in case the top hole wasn't centered exactly on the leg.
     
    #6 WilliamK, Jun 21, 2022
    Giarc and Peter Van Der Walt like this.

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice