Welcome to Our Community

Some features disabled for guests. Register Today.

Sign Up

Materials Speeds and Feeds Chart

Great speeds and feeds chart for 1/4" milling of lots of materials

  1. Mark Carew

    Mark Carew OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jun 28, 2013
    Messages:
    2,758
    Likes Received:
    2,441
    Mark Carew submitted a new resource:

    Materials Speeds and Feeds Chart - Great speeds and feeds chart for 1/4" milling of lots of materials

    Read more about this resource...
     
    #1 Mark Carew, Oct 13, 2018
    krazeekirk and GrayUK like this.
  2. GrayUK

    GrayUK Openbuilds Team Elder
    Staff Member Moderator Builder

    Joined:
    May 5, 2014
    Messages:
    1,668
    Likes Received:
    627
    I need to remember it's there!! :banghead::thumbsup::thumbsup:
     
    #2 GrayUK, Oct 13, 2018
    Mark Carew likes this.
  3. Mark Carew

    Mark Carew OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jun 28, 2013
    Messages:
    2,758
    Likes Received:
    2,441
    I print out these kind of charts and have them next to the computer where I do the toolpathing, so I can glance over and have the info needed while working. Really is a big help :thumbsup:
     
    #3 Mark Carew, Oct 13, 2018
    Edgar Stanbury and GrayUK like this.
  4. Giarc

    Giarc OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jan 24, 2015
    Messages:
    3,016
    Likes Received:
    1,682
    It was nice of them to include the Makita as well. I was just getting ready to make the conversions when I noticed it was already there.:thumbsup:
     
    #4 Giarc, Oct 13, 2018
    Mark Carew likes this.
  5. Miles Gregson

    Miles Gregson New
    Builder

    Joined:
    May 28, 2018
    Messages:
    12
    Likes Received:
    3
    This is great, thanks!
    A dumb question, is the feed rate inches/minute? I'm UK based.
    Cheers
     
    #5 Miles Gregson, Oct 15, 2018
  6. Mark Carew

    Mark Carew OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jun 28, 2013
    Messages:
    2,758
    Likes Received:
    2,441
    The feed is in inches/minute
     
    #6 Mark Carew, Oct 15, 2018
  7. Naiggel

    Naiggel New
    Builder

    Joined:
    Nov 19, 2018
    Messages:
    17
    Likes Received:
    2
    That's really helpfull!! I will print it also. (I own a workbee 1510)
    You say inches...If I give in artcam 65 feed and 25 plunge, which by the way I use mm, for milling acrylic is going like crazy. If I have to give inches I'm expecting flying like superman. :jawdrop::eek:

    Do I read it wrong? Sorry for my english and my noobidity. I'm new in cnc world. :(
    And what is the Doc category?

    Thanks!!
     
    #7 Naiggel, Feb 7, 2019
  8. Ariel Yahni

    Ariel Yahni OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Oct 22, 2015
    Messages:
    144
    Likes Received:
    496
    @Naiggel DOC = Depth of Cut. Means how much the Z axis will go down per each pass
     
    #8 Ariel Yahni, Feb 7, 2019
    Naiggel likes this.
  9. Naiggel

    Naiggel New
    Builder

    Joined:
    Nov 19, 2018
    Messages:
    17
    Likes Received:
    2
    Thanks Ariel!!
    Can you tell me about the feed and plunge?

    For example...for acrylic it says feed=65 and plunge=25 with speed 19000. Is that ok? Cause I'm little "scared" to put these on my machine. (or just noob):D
     
    #9 Naiggel, Feb 7, 2019
  10. Naiggel

    Naiggel New
    Builder

    Joined:
    Nov 19, 2018
    Messages:
    17
    Likes Received:
    2
    ok..I just did it...not bad at all.
    Thanks for your I answer.:thumbsup:
     
    #10 Naiggel, Feb 7, 2019
    Ariel Yahni likes this.
  11. Ariel Yahni

    Ariel Yahni OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Oct 22, 2015
    Messages:
    144
    Likes Received:
    496
    @Naiggel Be cautios of that information and always test if you are not sure. You can always speed up / down if you are using for example the OpenBuilds Control
     
    #11 Ariel Yahni, Feb 7, 2019
    Mark Carew and Naiggel like this.
  12. Naiggel

    Naiggel New
    Builder

    Joined:
    Nov 19, 2018
    Messages:
    17
    Likes Received:
    2
    Yeah I know...and yes I'm using OpenBuilds Control. Thanks!
     
    #12 Naiggel, Feb 7, 2019
  13. Alex Chambers

    Alex Chambers Master
    Moderator Builder

    Joined:
    Nov 1, 2018
    Messages:
    2,785
    Likes Received:
    1,365
    If it helps I have put a copy of that table in helpful tools with the conversions to mm/minute done. It's title is "speeds and feeds". Alex.
     
    #13 Alex Chambers, Feb 7, 2019
    Naiggel likes this.
  14. Naiggel

    Naiggel New
    Builder

    Joined:
    Nov 19, 2018
    Messages:
    17
    Likes Received:
    2
    thanks Alex, I think I understand now some things. I can't put the conversion from inches to mm!!
    I dont know why, but ArtCam have two different systems!

    When I choose bits with inches, feeds and plunge are in inches/min but when I use metric tools have mm/sec.
    Imagine putting 1651mm/sec!!!:banghead::banghead::banghead::cry::cry::cry:

    I don't know if there is something I can do to change that to mm/min!

    For now I will continue adding and trying with inches tools and will see!!:) (or devide feeds and plunge mm convertion with 60:thumbsup:)
     

    Attached Files:

    #14 Naiggel, Feb 7, 2019
    Last edited: Feb 7, 2019
  15. Mark Carew

    Mark Carew OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jun 28, 2013
    Messages:
    2,758
    Likes Received:
    2,441
    #15 Mark Carew, Apr 7, 2022
    Peter Van Der Walt likes this.

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice