Welcome to Our Community

Some features disabled for guests. Register Today.

Sign Up

FEEDHOLD

Discussion in 'Control Software' started by Steve Caldwell, Dec 7, 2023.

  1. Steve Caldwell

    Steve Caldwell New
    Builder

    Joined:
    Mar 28, 2022
    Messages:
    9
    Likes Received:
    0
    I've got a
    [14:18:32] [ [external from hardware] ] OpenBuilds CONTROL received a FEEDHOLD notification from Grbl: This could be due to someone pressing the HOLD button (if connected)"
    problem. Probe stops at touch point. Not sure what's causing the issue but it gives me no options to get out except abort.
     
    #1 Steve Caldwell, Dec 7, 2023
  2. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    15,523
    Likes Received:
    4,424
    Anything wired up to the Feedhold (Door) input?
     
    #2 Peter Van Der Walt, Dec 7, 2023
  3. Steve Caldwell

    Steve Caldwell New
    Builder

    Joined:
    Mar 28, 2022
    Messages:
    9
    Likes Received:
    0
    No door on the unit
     
    #3 Steve Caldwell, Dec 7, 2023
  4. Steve Caldwell

    Steve Caldwell New
    Builder

    Joined:
    Mar 28, 2022
    Messages:
    9
    Likes Received:
    0
    In the troubleshooting mode it has, under buttons: Off, Hold/Door, Off
     
    #4 Steve Caldwell, Dec 7, 2023
  5. Steve Caldwell

    Steve Caldwell New
    Builder

    Joined:
    Mar 28, 2022
    Messages:
    9
    Likes Received:
    0
    Hold door is in Red
     
    #5 Steve Caldwell, Dec 7, 2023
  6. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    15,523
    Likes Received:
    4,424
    Yes, but do you have anything wired to the DOOR port? An estop, or similar would count too. Anything wired?


    Or perhaps nonstandard Grbl Settings? Post a backup for review
     
    #6 Peter Van Der Walt, Dec 7, 2023
  7. Steve Caldwell

    Steve Caldwell New
    Builder

    Joined:
    Mar 28, 2022
    Messages:
    9
    Likes Received:
    0
    Yeah I do have an E-Stop, settings reversed?
     
    #7 Steve Caldwell, Dec 7, 2023
  8. Steve Caldwell

    Steve Caldwell New
    Builder

    Joined:
    Mar 28, 2022
    Messages:
    9
    Likes Received:
    0
    It started acting up bout the time I put it in.
     
    #8 Steve Caldwell, Dec 7, 2023
  9. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    15,523
    Likes Received:
    4,424
    Either wired wrong, configured wrong, or EMI.

    More importantly the Door input is for a Door switch.

    E-stops shouldn't be connected there. E-Stops should cut Power. Wall socket > E stop > Power strip > all machine accessories.
     
    #9 Peter Van Der Walt, Dec 7, 2023
    David the swarfer likes this.
  10. Steve Caldwell

    Steve Caldwell New
    Builder

    Joined:
    Mar 28, 2022
    Messages:
    9
    Likes Received:
    0
    I'll look but was pretty sure it was connected to the e-stop.
    Thanks, got to dig a little deeper
     
    #10 Steve Caldwell, Dec 7, 2023

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice