Welcome to Our Community

Some features disabled for guests. Register Today.

Sign Up

PnP 4 axis small/fast machine

Discussion in 'Other Builds' started by lewac, Jan 22, 2014.

PnP 4 axis small/fast machine

PnP 4 axis small/fast machine

Discussion in 'Other Builds' started by lewac, Jan 22, 2014.

You need some mechanical and electronic experience. This is NOT a novice undertaking! a familiarity with linux a plus (but not necessary). Basic woodworking and metal fabrication a big plus as well.

PnP pnp machine linuxCNC parallel port
  1. lewac

    lewac New
    Builder

    Joined:
    Jan 14, 2014
    Messages:
    2
    Likes Received:
    4
    lewac published a new build:

    Read more about this build...
     
    #1 lewac, Jan 22, 2014
  2. The Dude

    The Dude Well-Known
    Builder

    Joined:
    Jan 2, 2014
    Messages:
    243
    Likes Received:
    102
    I'm interested in trying this but as an add-on to the routy I'm building. I already have a RTOS LinuxCNC with parallel port TB6560 and optical(IR LED) home switches. I don't know how accurate it will be yet but the motors can do 1.8 deg per step and I think the controller does 1/32 microstepping. Think it will work?
     
    #2 The Dude, Jan 22, 2014
  3. lewac

    lewac New
    Builder

    Joined:
    Jan 14, 2014
    Messages:
    2
    Likes Received:
    4
    That will certainly work. however you don't require ANY microstepping for a router (unless you are make really tiny things). You do need IR home switches though (not physical ones, they bounce and are way too slow for definitive work). typical routers though are not in much of a hurry to do anything as most assuredly you'll burn the work up and/or your cutting tool!
     
    #3 lewac, Feb 14, 2014
  4. cooldan

    cooldan New
    Builder

    Joined:
    Mar 7, 2014
    Messages:
    3
    Likes Received:
    0
    http://xdztst.netii.net/

    check out this project i made... you need a OpenGL compatible browser ( notice, it works correctly if show some FPS counter on left side of screen and some arrows near the textbox's to change the XYZ values... then it submit.
     
    #4 cooldan, Apr 2, 2014
  5. Tweakie

    Tweakie OpenBuilds Team
    Moderator

    Joined:
    Jan 18, 2014
    Messages:
    784
    Likes Received:
    326
    Hi Cooldan,

    Welcome to the forum.

    I give up, what is it ??

    Tweakie.
     
    #5 Tweakie, Apr 3, 2014
  6. Mark Carew

    Mark Carew OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jun 28, 2013
    Messages:
    2,758
    Likes Received:
    2,440
    Not showing up in Chrome :cry:
     
    #6 Mark Carew, Apr 3, 2014
  7. cooldan

    cooldan New
    Builder

    Joined:
    Mar 7, 2014
    Messages:
    3
    Likes Received:
    0
    hi, and thanks.. well it should work in chrome.. i think the animation only work in chrome.. try to update it...

    its some robot arm, i make the code for arduino control 3 servos (180º) so the robot "hand" move as a CNC... with XYZ coordinates...

    im sorry for the bad english :p if anyone is interested i can share the code and the concept :p
     
    #7 cooldan, Apr 3, 2014
  8. Mark Carew

    Mark Carew OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jun 28, 2013
    Messages:
    2,758
    Likes Received:
    2,440
    That sounds very cool but cannot get it to work.
    It will not show up at all in Chrome (latest version) but does show up in IE and I can rotate it around zoom in and out and such but thats it the submit does nothing at this point for me at least.
    Capture.JPG
     
    #8 Mark Carew, Apr 3, 2014
  9. cooldan

    cooldan New
    Builder

    Joined:
    Mar 7, 2014
    Messages:
    3
    Likes Received:
    0


    well were is the "real" arm :p its my first prototype xD

    it work in my chrome, it must have WEBGL activated, it should look like this... [​IMG]

    and move after hit submit...

    last try, check this website: http://threejs.org/ if any of the samples work, my site should work too..

    thanks for the replys :)
     
    #9 cooldan, Apr 6, 2014
  10. Mark Carew

    Mark Carew OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jun 28, 2013
    Messages:
    2,758
    Likes Received:
    2,440
    Ok it's working now (needed hardware acceleration turned on in Chrome settings) very cool the way it moves nice job!
    http://xdztst.netii.net/
     
    #10 Mark Carew, Apr 6, 2014
  11. David the swarfer

    David the swarfer OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Aug 6, 2013
    Messages:
    3,461
    Likes Received:
    1,915
    you need to replace all those servos with metal gear digitals. this will give you much higher resolution and smoother movement, though I suspect some of your jitters are from your software. digital servos could be updated at 400hz so you could micro step from position to position.
     
    #11 David the swarfer, Apr 8, 2014
  12. David the swarfer

    David the swarfer OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Aug 6, 2013
    Messages:
    3,461
    Likes Received:
    1,915
    if you use belt/chain/cable drives, you DO need microstepping (unless you have some sort of reduction between the motor and the belt drive, but even then...)
    in general, stepper motors run better with microstepping as it helps to avoid resonance, so use it if you have it even if your application does not need it for resolution.

    what is a typical router? my woodworking router spins at 24000 rpm and cuts as fast as I can push it. in fact if I feed too slow, THAT is when it burns the wood. advocating slow feed speeds is counter to the science of cutting.
    The CNC router I use will happily cut plywood at 2000mm/min at 30000rpm.
    Please see my extensive posting on feed speeds in the OX build thread.
    In short, use existing science to calculate feed speed. If your machine is not stiff enough at that speed, reduce only the depth of cut, for example, with a 1/8" bit, instead of 1/16" depth, use 1/32" per pass.
     
    #12 David the swarfer, Apr 8, 2014
  13. Tweakie

    Tweakie OpenBuilds Team
    Moderator

    Joined:
    Jan 18, 2014
    Messages:
    784
    Likes Received:
    326
    Excellent advice David. :thumbsup:

    Tweakie.
     
    #13 Tweakie, Apr 8, 2014
  14. gary krig

    gary krig New
    Builder

    Joined:
    Jan 10, 2022
    Messages:
    2
    Likes Received:
    0
    I cannot find the pnp 4 axis machine?
     
    #14 gary krig, Feb 9, 2022
  15. Mark Carew

    Mark Carew OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jun 28, 2013
    Messages:
    2,758
    Likes Received:
    2,440
    #15 Mark Carew, Feb 10, 2022
  16. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    15,050
    Likes Received:
    4,313
    #16 Peter Van Der Walt, Feb 10, 2022
  17. gary krig

    gary krig New
    Builder

    Joined:
    Jan 10, 2022
    Messages:
    2
    Likes Received:
    0
    Thanx.
    I will look at those......
    Gary
     
    #17 gary krig, Feb 14, 2022
  18. ljvb

    ljvb Well-Known
    Builder

    Joined:
    Feb 14, 2019
    Messages:
    276
    Likes Received:
    87
    Not cheap.. not expensive.. for what it is, but Opulo is a pnp based on the Acro.. originally, not much left of the original acro. It is by Stephan Hawes, it is fully opensource (even the custom board he built to control it), but he has kits available. You will need a 3d printer to make the plastic bits.
     
    #18 ljvb, Feb 14, 2022

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice