Welcome to Our Community

Some features disabled for guests. Register Today.

Sign Up

Openbuilds Xtension Connector Lid for Nema 23 Cover 2019-02-12

Xtension connector lid for motor cover.

  1. sharmstr

    sharmstr OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 23, 2018
    Messages:
    2,059
    Likes Received:
    1,448
    #1 sharmstr, Feb 12, 2019
  2. Adam Filipowicz

    Adam Filipowicz Journeyman
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    261
    Likes Received:
    135
    Nice Job!
     
    #2 Adam Filipowicz, Feb 23, 2019
    sharmstr likes this.
  3. Netechsys

    Netechsys Journeyman
    Builder

    Joined:
    Mar 25, 2020
    Messages:
    149
    Likes Received:
    108
    Hello.. Ok.. I am having a problem with the attached file.. I have downloaded the body from Thingverse, and will be printing it shortly. But, I can not get the lid above to scale to the right size for this. When I open the STL, it is only like 1.x mm wide. And I can not get it to scale to the right size.. I have tried in Vectric and Freecad.... No luck on either.. Any help would be greatly appreciated!

    Ok.. I am going to give up on this.. I tried F360, and now the body is huge! I give up on scaling.... Just not clicking tonight..
     
    #3 Netechsys, Feb 10, 2021
    Last edited: Feb 10, 2021
  4. Christian James

    Christian James Journeyman
    Builder

    Joined:
    Jun 8, 2018
    Messages:
    461
    Likes Received:
    218
    Use Netfabb to scale it. Where is the attached file by the way?
     
    #4 Christian James, Feb 10, 2021
  5. Netechsys

    Netechsys Journeyman
    Builder

    Joined:
    Mar 25, 2020
    Messages:
    149
    Likes Received:
    108
    Up at the top.
    4076AE9B-CCD2-4CF8-ABE3-380AA5DF4BD3.jpeg
     
    #5 Netechsys, Feb 10, 2021
  6. Christian James

    Christian James Journeyman
    Builder

    Joined:
    Jun 8, 2018
    Messages:
    461
    Likes Received:
    218
    Haha, its the old mm/inch problem. scale it up by 25.4 and its good.
     

    Attached Files:

    #6 Christian James, Feb 10, 2021
    sharmstr likes this.
  7. JustinTime

    JustinTime Veteran
    Builder

    Joined:
    Dec 18, 2013
    Messages:
    784
    Likes Received:
    259
    I found that importing .stl files into Fusion360 they are 10 times the original size. I use the Scale feature to select the imported model and then enter 0.1 for the new scale and it, so far, always came out the perfect size.
     
    #7 JustinTime, Feb 10, 2021
    Giarc likes this.
  8. sharmstr

    sharmstr OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 23, 2018
    Messages:
    2,059
    Likes Received:
    1,448
    File was created in inches within Fusion.
     
    #8 sharmstr, Feb 10, 2021
    Peter Van Der Walt likes this.

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice