Welcome to Our Community

Some features disabled for guests. Register Today.

Sign Up

Search Results

Search Again
Page 2 of 4
  1. David Kater
    Post

    X-axis doesn’t back up from limit switch when homing

    I did loosen the collars, and then the diagonals go quite well! I will attach a video of it
    Post by: David Kater, Apr 1, 2022 in forum: Controller Boards
  2. David Kater
    Post

    X-axis doesn’t back up from limit switch when homing

    Jogging in 1 direction is smooth and stutter free. Diagonals still stutter a lot. But when homing moves diagonally, it all runs smooth! Really weird..
    Post by: David Kater, Apr 1, 2022 in forum: Controller Boards
  3. David Kater
    Post

    X-axis doesn’t back up from limit switch when homing

    Alright! I have the jogging sorted, that is all fine, I will apply that mask with no. 1, hope it works!
    Post by: David Kater, Mar 31, 2022 in forum: Controller Boards
  4. David Kater
    Post

    X-axis doesn’t back up from limit switch when homing

    These are the settings from the fresh reset
    Post by: David Kater, Mar 31, 2022 in forum: Controller Boards
  5. David Kater
    Post

    X-axis doesn’t back up from limit switch when homing

    Now i did a fresh install, reset everything, and switched the wires arround so the jogging directions are right. When I press home, x goes to...
    Post by: David Kater, Mar 31, 2022 in forum: Controller Boards
  6. David Kater
    Post

    X-axis doesn’t back up from limit switch when homing

    Only problem is, I don't have enough wire length to change to switches to maximum, so is there a workaround for that?
    Post by: David Kater, Mar 31, 2022 in forum: Controller Boards
  7. David Kater
    Post

    X-axis doesn’t back up from limit switch when homing

    Alright, I will change that! I did built the machine correctly, but RatRig, from which I bought the machine, has the switches located on different...
    Post by: David Kater, Mar 31, 2022 in forum: Controller Boards
  8. David Kater
    Post

    X-axis doesn’t back up from limit switch when homing

    I think this is the most recent one
    Post by: David Kater, Mar 31, 2022 in forum: Controller Boards
  9. David Kater
    Post

    X-axis doesn’t back up from limit switch when homing

    The standard one from RatRig, 350watt, 24V, 14.6a. Running on 240 volts
    Post by: David Kater, Mar 31, 2022 in forum: Controller Boards
  10. David Kater
    Post

    X-axis doesn’t back up from limit switch when homing

    Sorry, my bad!
    Post by: David Kater, Mar 31, 2022 in forum: Controller Boards
  11. David Kater
    Post

    X-axis doesn’t back up from limit switch when homing

    X runs really smooth too, even better than the Y's
    Post by: David Kater, Mar 31, 2022 in forum: Controller Boards
  12. David Kater
    Post

    X-axis doesn’t back up from limit switch when homing

    I did this on the Y, and they are spinning freely. I also pressed home all axis, while the leadscrews were disconnected. The next thing happened,...
    Post by: David Kater, Mar 31, 2022 in forum: Controller Boards
  13. David Kater
    Post

    X-axis doesn’t back up from limit switch when homing

    I did align them within 30 microns, and the minimum is 40, so that should be good. When there werent any screws installed, it was buttery-smooth,...
    Post by: David Kater, Mar 30, 2022 in forum: Controller Boards
  14. David Kater
    Post

    X-axis doesn’t back up from limit switch when homing

    But doesn’t it lose steps because of the stutter?
    Post by: David Kater, Mar 30, 2022 in forum: Controller Boards
  15. David Kater
    Post

    X-axis doesn’t back up from limit switch when homing

    I checked all of that, and everything is tight. Checked for backlash, nothing there. Loosened and re-tightened leadscrew nuts, and couplers, also...
    Post by: David Kater, Mar 30, 2022 in forum: Controller Boards
  16. David Kater
    Post

    X-axis doesn’t back up from limit switch when homing

    I did a test cut, and something definitely is not right here. When jogging 1 axis at a time all is fine, but in this g code there were some steps...
    Post by: David Kater, Mar 30, 2022 in forum: Controller Boards
  17. David Kater
    Post

    X-axis doesn’t back up from limit switch when homing

    Alright, i will do that! On the topic of EMI, I have not yet grounded my shielded cables, could that be a problem?
    Post by: David Kater, Mar 30, 2022 in forum: Controller Boards
  18. David Kater
    Post

    X-axis doesn’t back up from limit switch when homing

    Yeah i did that, but then it didn’t have enough room to do all the toolpaths, because the letters are too small for an 8mm endmill
    Post by: David Kater, Mar 30, 2022 in forum: Controller Boards
  19. David Kater
    Post

    X-axis doesn’t back up from limit switch when homing

    [ATTACH] [ATTACH] This is how I have got the wires running now, still the same problem, but I don’t have much more room to spread them further
    Post by: David Kater, Mar 30, 2022 in forum: Controller Boards
  20. David Kater
    Post

    X-axis doesn’t back up from limit switch when homing

    I only have a 8mm collet for my spindle at the moment, is there a different test that i can run that you recommend?
    Post by: David Kater, Mar 30, 2022 in forum: Controller Boards
Showing results 21 to 40 of 67 Next >
Search Again
Page 2 of 4
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice