Welcome to Our Community

Some features disabled for guests. Register Today.

Sign Up

Search Results

Search Again
Page 3 of 10
  1. Peter Van Der Walt
    Post

    YL620-A VFD Settings

    We don't have this particular model on hand, so best to refer to the included manual and confirm
    Post by: Peter Van Der Walt, Jan 23, 2022 in forum: CNC Mills/Routers
  2. Peter Van Der Walt
    Post

    At a loss with error 9..

    And the Vectric and gcode files. So we can see what the OP sent, how he set up his job, and the resultant error (screenshot shows lead up and...
    Post by: Peter Van Der Walt, Jan 23, 2022 in forum: General Talk
  3. Peter Van Der Walt
    Post

    Breaking Aluminum Couplers - 6.5-10mm

    Ps: our motors are 6.35mm (1/4 inch) not 6.5mm. Not sure of that contributed to your breakage, as the motor shaft would be more offset than...
    Post by: Peter Van Der Walt, Jan 23, 2022 in forum: CNC Mills/Routers
  4. Peter Van Der Walt
    Post

    YL620-A VFD Settings

    See:
    Post by: Peter Van Der Walt, Jan 23, 2022 in forum: CNC Mills/Routers
  5. Peter Van Der Walt
    Post

    Interface Blank (white) screen

    Test it in a warmer room just a step to eliminate that as a cause?
    Post by: Peter Van Der Walt, Jan 22, 2022 in forum: Interfaces
  6. Peter Van Der Walt
    Post

    File transfer to new Interface controller

    See firmware/CHANGELOG.txt at main · OpenBuilds/firmware added between V1.30 and V1.36 - keep your firmware up to date (: Type the IP shown...
    Post by: Peter Van Der Walt, Jan 22, 2022 in forum: General Talk
  7. Peter Van Der Walt
    Post

    Breaking Aluminum Couplers - 6.5-10mm

    They shouldn't break, unless operated at rather large off angle, off axis or stretched. Show us then in-use application and we'd be happy to help...
    Post by: Peter Van Der Walt, Jan 22, 2022 in forum: CNC Mills/Routers
  8. Peter Van Der Walt
    Post

    How to use variables in openbuilds macro's?

    You can use the Javacript macro functionality - with it you can even build UIs to enter the values into your variables. See Getting started with...
    Post by: Peter Van Der Walt, Jan 22, 2022 in forum: CAM
  9. Peter Van Der Walt
    Post

    Adding a CNC controlled table on top of the table on my CNC Mill.

    Interface is just a "user interface". See docs.openbuilds.com and in particular docs.openbuilds.com/blackbox and docs.openbuilds.com/interface
    Post by: Peter Van Der Walt, Jan 21, 2022 in forum: CNC Mills/Routers
  10. Peter Van Der Walt
    Post

    X Y calibration

    You can point users at the video: [MEDIA]
    Post by: Peter Van Der Walt, Jan 21, 2022 in forum: General Talk
  11. Peter Van Der Walt
    Post

    YL620-A VFD Settings

    P00.01 and P07.08 Refer the manual for more info
    Post by: Peter Van Der Walt, Jan 21, 2022 in forum: CNC Mills/Routers
  12. Peter Van Der Walt
    Post

    OpenBuilds Control and RPi

    Note the version it was tested against is mentioned in the Wiki (not latest as instructions hasn't been updated in a couple months) Follow the...
    Post by: Peter Van Der Walt, Jan 21, 2022 in forum: Control Software
  13. Peter Van Der Walt
    Post

    Lead 1010 to 1015 conversion

    Remember to also add the tensioning system for 1500mm axes. Watch the LEAD1515 video to gain further information on how that is assembled, the...
    Post by: Peter Van Der Walt, Jan 21, 2022 in forum: CNC Mills/Routers
  14. Peter Van Der Walt
    Post

    Upgrading OLd Shapeoko 3 to OPenbuild Blackbox 4

    Yes, see docs.openbuilds.com/blackbox
    Post by: Peter Van Der Walt, Jan 21, 2022 in forum: CNC Mills/Routers
  15. Peter Van Der Walt
    Post

    UGS vs CONTROL

    Unfortunately time to move on - 1.0.9 won't work with with Grbl 1.1 - not that hard to use new software though and you are missing out on awesome...
    Post by: Peter Van Der Walt, Jan 20, 2022 in forum: CNC Mills/Routers
  16. Peter Van Der Walt
    Post

    UGS vs CONTROL

    See OpenBuilds Software - FREE Software for CNC Control: OpenBuilds CONTROL and OpenBuilds CAM and try out CONTROL Also see...
    Post by: Peter Van Der Walt, Jan 20, 2022 in forum: CNC Mills/Routers
  17. Peter Van Der Walt
    Post

    Connecting Interface to XPro V4

    Same thread, just different number (thread was cleaned of older spam a while back): See...
    Post by: Peter Van Der Walt, Jan 20, 2022 in forum: Interfaces
  18. Peter Van Der Walt
    Post

    Openbuilds 4x8 cnc

    Yes, you still stream gcode using CONTROL: See docs:software:overview [OpenBuilds Documentation] CAM side you can use OpenBuildsCAM or Fusion360...
    Post by: Peter Van Der Walt, Jan 20, 2022 in forum: CNC Mills/Routers
  19. Peter Van Der Walt
    Post

    Openbuilds 4x8 cnc

    Yes it can: See docs:blackbox:connect-plasma [OpenBuilds Documentation] also see [MEDIA] and the follow up (Get a non-HF plasma to avoid issues...
    Post by: Peter Van Der Walt, Jan 20, 2022 in forum: CNC Mills/Routers
  20. Peter Van Der Walt
    Post

    C-Beam xlarge linear actuator.

    See How to calculate V-Slot® deflection 80lbs is quite a bit outside the usual use case, so unlikely to be a good idea.
    Post by: Peter Van Der Walt, Jan 19, 2022 in forum: CNC Mills/Routers
Showing results 41 to 60 of 197 Next >
Search Again
Page 3 of 10
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice