Welcome to Our Community

Some features disabled for guests. Register Today.

Sign Up

blackbox

Page 3 of 7
  1. Johnny Reich
    Thread

    BlackBox Y2 stepper driver short?

    I’m using an OpenBuilds BlackBox to control a 3-axis mill. When initially connecting all leads to the 3 axes, spindle motor control board and...
    Thread by: Johnny Reich, Dec 24, 2021, 3 replies, in forum: Controller Boards
  2. Christian Price
    Thread

    I rushed in and now I need help

    Hello, Im completely new to cnc's but I saw a few cnc woodcraft videos and I started building a custom cnc but now I'm dead in the water. Im using...
    Thread by: Christian Price, Dec 19, 2021, 9 replies, in forum: General Electronics
  3. UltiBots
    Thread

    VFD & IOT... how to wire/configure BlackBox

    Hi all - I upgraded my Dewalt 611 to a 1.5kW VFD spindle. Before the mod I used the IOT relay to power the router and flood pump from BlackBox's...
    Thread by: UltiBots, Dec 7, 2021, 8 replies, in forum: CNC Mills/Routers
  4. Two Tool Designs
    Thread

    K40 - BlackBox wiring

    Hi friends, I have searched the forums and writeups on how to specifically wire up the Blackbox to the K40 Power supply (24V, G, 5V, L) but I am...
    Thread by: Two Tool Designs, Dec 7, 2021, 20 replies, in forum: Laser Cutters
  5. Steve French 17
    Thread

    My BlackBox and Limit Switches failed in the most unexpected way

    So - today I'm milling a sign and it starts up just fine - it runs for a few minute and I leave it unattended. I check on it about 20 minutes...
    Thread by: Steve French 17, Nov 17, 2021, 8 replies, in forum: CNC Mills/Routers
  6. Johnny Reich
    Thread

    Intelitek ProLight 1000 Mill Retrofit

    A few months back I posted about acquiring an old Light Machines (now Intelitek) ProLight 1000 CNC Mill from a local high school. My intentions...
    Thread by: Johnny Reich, Nov 14, 2021, 4 replies, in forum: Other Builds
  7. Heather Meaney
    Thread

    Touch Probe shorted Blackbox, Firmware Error

    Hi, I'm not electronic-savvy so please bare with me. I was using the touch probe, and after completing the probe I removed the magnet from the...
    Thread by: Heather Meaney, Nov 1, 2021, 6 replies, in forum: Controller Boards
  8. Micah Beckman
    Thread

    Python Serial Communication with Blackbox

    I'm getting different responses from the Blackbox (using pyserial) depending on whether or not the OpenBuilds CONTROL software is connected to the...
    Thread by: Micah Beckman, Oct 11, 2021, 2 replies, in forum: General Talk
  9. Roman Hryntsiv
    Thread

    Try to control two solenoids at the same time

    Is there any way to control two solenoids by using BlackBox at the same time? I have two 24V solenoids that I would like to control...
    Thread by: Roman Hryntsiv, Oct 4, 2021, 3 replies, in forum: Controller Boards
  10. Fredrik Carlsson
    Thread

    Y2 Redlight

    Hey! I have done some cutting with my Openbuilds controller today. Suddenly when i go to jog the machine i notice only one Y motor is turning. I...
    Thread by: Fredrik Carlsson, Oct 4, 2021, 7 replies, in forum: Controller Boards
  11. cranktown
    Thread

    Co2 Laser cutter/engraver using the OpenBuilds BlackBox

    Just converted my CNC laser over to use the the BlackBox motion control system, and so far, I really dig it! Super easy setup, and thus far has...
    Thread by: cranktown, Oct 1, 2021, 33 replies, in forum: Laser Cutters
  12. Michael Sheldon
    Thread

    Handibot BlackBox conversion

    I have an original Kickstarter Handibot that never got much use. Keeping a Windows laptop just to run it was a bit annoying, and they never did...
    Thread by: Michael Sheldon, Sep 18, 2021, 7 replies, in forum: CNC Mills/Routers
  13. 5thstreetfab
    Thread

    Need Help with BlackBox and Interface

    Hey guys. I really don't know much about cnc, so any help would be awesome! I hooked up the blackbox and the interface. The machine will move...
    Thread by: 5thstreetfab, Aug 21, 2021, 1 replies, in forum: General Talk
  14. Nathan Allaire
    Thread

    How to feed G-Code to Blackbox via Arduino Uno

    I am in the process of building a CNC that is controlled by the Openbuilds Blackbox. Instead of using the Openbuilds CONTROL to pass the G-Code to...
    Thread by: Nathan Allaire, Aug 11, 2021, 25 replies, in forum: Controller Boards
  15. antang808
    Thread

    Just set up a Workbee (from SPAM) + BlackBox but motors aren't working, is it wrong wiring?

    So I just finished the wiring for my first Workbee and I admit that I cheaped out on the mechanical kit from SPAM but I made sure to get a...
    Thread by: antang808, Aug 5, 2021, 6 replies, in forum: Motors
  16. joeatbjk
    Thread

    Blackbox construction material

    What material is the blackbox made of? The BlackBox Top Panel BlackBox Bottom Panel BlackBox Back Panel BlackBox Front Panel Link for...
    Thread by: joeatbjk, Jul 25, 2021, 2 replies, in forum: General Talk
  17. Lars Plovmann
    Thread

    Making laser ingraver

    Hii all. Im a brand new member off your Fora :) Im from Denmark, and have a laser, Dremel CNC and some Prusa 3d printers. Now i make a new...
    Thread by: Lars Plovmann, Jul 14, 2021, 4 replies, in forum: Laser Cutters
  18. Marcsallent
    Thread

    Blackbox Nema 17 initial parameters

    Hello! I purchased an ACRO 1510 building kit with a BlackBox several months ago and just now I have been able to start working on the project....
    Thread by: Marcsallent, Jul 9, 2021, 3 replies, in forum: Controller Boards
  19. SoFreshDetails
    Thread

    CNC keeps stopping

    Hi, I hope someone can help me, I have recently purchased a CNC router but it keeps stopping (crashing) at random points or time. i have tried...
    Thread by: SoFreshDetails, Jun 29, 2021, 7 replies, in forum: CNC Mills/Routers
  20. Federico77
    Thread

    Broken Blackbox current adjustment potentiometers

    Hello guys, I had a bad day today with my Workbee and Blackbox. First of all I noticed that my X axis started skipping steps although doing easy...
    Thread by: Federico77, May 29, 2021, 4 replies, in forum: Controller Boards
Showing results 41 to 60 of 140
Page 3 of 7
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice