Welcome to Our Community

Some features disabled for guests. Register Today.

Sign Up

cnc

Page 1 of 10
  1. Peter Bohr
    Thread

    Lead Screw moving way less than the set value

    Okay so I am a beginner and don't have much experience with the CNC systems. I am trying to build a custom system and for now I am just focusing...
    Thread by: Peter Bohr, Apr 17, 2025, 9 replies, in forum: General Talk
  2. Drew-SR388
    Thread

    Dual motor/sensor axis

    I currently have a cnc router where the Y-axis is controlled by two separate stepper motors and drivers. These are driven through linear rails...
    Thread by: Drew-SR388, Mar 6, 2025, 3 replies, in forum: General Electronics
  3. dave_michigan
    Thread

    Modular Enclosure: Dust Extraction and Wire Routing, where?

    Hello, I was just curious where you all route your wires and tubes for dust extraction and wiring? I have a modular enclosure that I built but...
    Thread by: dave_michigan, Mar 5, 2025, 2 replies, in forum: CNC Mills/Routers
  4. Jake2kuk
    Thread

    Ultimate Bee XPRO V5 Issues - erratic cutting behavior

    I have an Ultimate Bee 500x500 with XPRO V5 GRBL controller, and I use Vcarve with open builds GRBL (inch) post-processor. I also use the...
    Thread by: Jake2kuk, Oct 11, 2024, 0 replies, in forum: CNC Mills/Routers
  5. Jorge Luis Montes Eljach
    Thread

    Questions about BlackBox X32 (External Drivers Mod, Stepper Driver IC)

    Hi everyone, I’m working on a couple of projects for my university and I’m looking for some advice on using the BlackBox X32 (BBX32). I’ll break...
    Thread by: Jorge Luis Montes Eljach, Oct 9, 2024, 1 replies, in forum: Controller Boards
  6. Emanuel96
    Thread

    CNC Build HELP

    Hello everyone, I am planning to build my first CNC ATC, and after many hours of internet research i am confident that can be done, i just need a...
    Thread by: Emanuel96, Oct 4, 2024, 0 replies, in forum: CNC Mills/Routers
  7. dave_michigan
    Thread

    How would you fasten Granite to a Modular Table?

    Let's say I have an extra slab or two or granite laying around, just hypothetically wanted to use it for an Open Builds Modular Table top, for a...
    Thread by: dave_michigan, Jul 18, 2024, 3 replies, in forum: General Talk
  8. Kabs
    Thread

    Grbl Solid Handshaking

    In Grbl the 'ok' response cannot be used for handshaking because it is returned by Grbl after each command is sent to signal that it has...
    Thread by: Kabs, Jun 8, 2024, 14 replies, in forum: Control Software
  9. Jack Ness
    Thread

    Measurement is WAY off when I hit jog

    I have a new Vevor S4040 with a 400 x 400 workspace CNC. Just got it and in Gsender I clicked the Flash button...bad idea...everything went very...
    Thread by: Jack Ness, May 30, 2024, 3 replies, in forum: General Talk
  10. Oleks Lytv
    Thread

    multifunctional CNC machine

    I would like to initiate a discussion about an project idea - the creation of a multifunctional CNC machine. This idea arose from my desire to...
    Thread by: Oleks Lytv, May 5, 2024, 14 replies, in forum: Concepts and Ideas
  11. Upamanyu Ray
    Thread

    Spindle ramp down

    I recently purchased the openbuilds motion control x32. Really loved the software, and the plug-play type hardware. I am connecting my existing...
    Thread by: Upamanyu Ray, Apr 25, 2024, 2 replies, in forum: Control Software
  12. TheMinimaliiiist
    Thread

    Where to start - router CNC build

    Hi guys, I am Martin, 37, business owner from France. I would like to build my own router CNC machine as well as a router CNC lathe to be used...
    Thread by: TheMinimaliiiist, Apr 4, 2024, 1 replies, in forum: CNC Lathes
  13. Brad Winter
    Thread

    Best CNC for making Baseball Bats

    What is the best model of OpenBuild CNC wood lathes for carving different sizes and shapes of baseball bats? Thank you in advance. Brad
    Thread by: Brad Winter, Feb 1, 2024, 2 replies, in forum: CNC Lathes
  14. Ken Ewald
    Thread

    Is this even possible?

    HI, Old man learning new stuff. I'm thinking about building a custom CNC machine to use in creating clarinet bells. The concept is that the...
    Thread by: Ken Ewald, Jan 16, 2024, 13 replies, in forum: General Talk
  15. MFino
    Thread

    CNC Build Direction Needed

    Hey Everyone, I have a project in mind, but I am not sure where to start. My idea is to build a large enough CNC machine either 5 axis or 3...
    Thread by: MFino, Dec 23, 2023, 1 replies, in forum: General Talk
  16. CuttingDutchman
    Thread

    Question: Attach CNC directly to metal table

    Hello OpenBuilds forum members. I'm currently designing a CNC machine measuring 2000mm x 1200mm. I've observed the elevated prices of aluminum...
    Thread by: CuttingDutchman, Oct 16, 2023, 1 replies, in forum: CNC Mills/Routers
  17. Anne Lanting
    Thread

    Go to zero: first move Z up then move X and Y

    Hello, I recently built my own CNC router. it's small but works pretty well. i'm learning gcode but i can't figure out the following: after the...
    Thread by: Anne Lanting, Jun 29, 2023, 3 replies, in forum: CNC Mills/Routers
  18. kajlo30
    Thread

    Limit Switch

    Hello,i would like to use limit switch only on two axes X,Y.Is there a way to use two of them?Am using the black box controller.Thanks.
    Thread by: kajlo30, Jun 8, 2023, 17 replies, in forum: General Talk
  19. A.J.W.E. Klappe
    Project

    Jubilee Board Horse Riding School

    Because this slice of a tree trunk is not flat at all, I had to make it flat first. I put it on my CNC table and tried to get it as flat as...
    Posted by: A.J.W.E. Klappe, Jun 2, 2023 in category: Signs & Plaques
  20. Steve Kilgore
    Thread

    Help Please!

    Hey, everyone! New here! My friend and I are building a 1515 CNC Router and we are having some problems. So we got everything wired up & the...
    Thread by: Steve Kilgore, Apr 7, 2023, 1 replies, in forum: General Talk
Showing results 1 to 20 of 200
Page 1 of 10
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice