Welcome to Our Community

Some features disabled for guests. Register Today.

Sign Up

grbl

Page 1 of 5
  1. ThrivenGeek
    Thread

    State of Machine and Interface firmware post closure

    I didn't see much discussion on here about this topic so I figured I would ask. What will happen to the machine firmware for the BlackBox and...
    Thread by: ThrivenGeek, Jun 6, 2025, 3 replies, in forum: General Talk
  2. Cliff 125
    Thread

    Black box x 32 red lights

    Hi All I have am issue. I keep getting the red lights coming on and the axis stop moving. From yesterday everything worked fine in terms of...
    Thread by: Cliff 125, Jan 26, 2025, 3 replies, in forum: CNC Mills/Routers
  3. PMO-451
    Thread

    GRBL and UGS custom path and dwell code

    Hello all, still working on my first build. I have done some searching on google and through the forum, and I can't seem to find any info on this...
    Thread by: PMO-451, Sep 11, 2024, 1 replies, in forum: Control Software
  4. steeeve
    Thread

    stand-alone GRBL board/firmware that retains user origin if the gcode is stopped part way through

    Hoping that you can suggest a small 3d controller board (intended for a router) that can operate stand-alone and for which the firmware does not...
    Thread by: steeeve, Aug 24, 2024, 4 replies, in forum: Controller Boards
  5. PMO-451
    Thread

    GRBL settings for stepper motor

    Hi everyone, This is my first project, so apologies if some of this is commonly asked. I am making a two axis machine that will carry a sensor...
    Thread by: PMO-451, Aug 24, 2024, 2 replies, in forum: Motors
  6. skimslozo
    Thread

    Blackbox reset after streaming GCODE via serial

    Hi all, I'm streaming GCODE directly to my Blackbox X32 via serial in a small Python script. The serial port is opened, GCODE commands are...
    Thread by: skimslozo, Aug 14, 2024, 3 replies, in forum: Control Software
  7. Elias Heuninck
    Thread

    M2 Program end - unwanted behaviour for servo

    Hello, I have an Acro 1510 with a Blackbox that I use as a pen plotter where a servo does the pen movements. I turn SVG's into Gcode with Sameer...
    Thread by: Elias Heuninck, Jul 29, 2024, 2 replies, in forum: Control Software
  8. Kabs
    Thread

    Grbl Solid Handshaking

    In Grbl the 'ok' response cannot be used for handshaking because it is returned by Grbl after each command is sent to signal that it has...
    Thread by: Kabs, Jun 8, 2024, 14 replies, in forum: Control Software
  9. Jonah B
    Thread

    Gcode Radius issue, G3 using G91, Openbuilds Control

    Hello, I am new to all of this so bare with me. Context: I am building a custom machine using the C beam XY gantry in conjunction with a 2x72...
    Thread by: Jonah B, Apr 18, 2024, 4 replies, in forum: CAM
  10. Adi_svp
    Thread

    Suppressing limit switch function

    I am trying to use grbl for tangential knife cutting . I want to use XYZ limit switches. I don't want limit switch function for A axis ,but only...
    Thread by: Adi_svp, Jan 29, 2024, 2 replies, in forum: Controller Boards
  11. Rik Plekker
    Thread

    Error 15. How to fix this.

    Goodday, I have a stronghold one 1250x 1250mm. With a blackbox x32 and openbuild control. I choosed the openbuild lead 1515 as a setup point....
    Thread by: Rik Plekker, Nov 26, 2023, 10 replies, in forum: OpenBuilds Forum Help
  12. Tulkas
    Thread

    Question about Blackbox X32 features and sending/receiving commands via USB connection.

    Hi everyone, I have a question about the Blackbox X32 for a work project. I’m very new new to CNC projects but I do have a good amount of...
    Thread by: Tulkas, Sep 17, 2023, 2 replies, in forum: General Talk
  13. domio
    Thread

    Python Connection to Blackbox grbl and sending G-Code

    Hi there, I'm trying to establish a connection to grbl on the X32 blackbox through the serial port. I haven't found anything that works out of...
    Thread by: domio, Aug 28, 2023, 2 replies, in forum: Control Software
  14. adam kimbrell
    Thread

    GRBL feed rate issue

    I have a nema 23 stepper controlled by arduino uno and tb6600 driver. Using universal g-code platform. Max feedrate set at 5000 mm/min. Ran g...
    Thread by: adam kimbrell, Aug 16, 2023, 6 replies, in forum: General Talk
  15. John Faik
    Thread

    [RHINOCAM] Safe Z above material

    I need to inquire about setting the safe Z distance above material at start of the gcode. - is it a setting already set or modfied ? - When I...
    Thread by: John Faik, Jul 18, 2023, 3 replies, in forum: CNC Mills/Routers
  16. Isaiah Baker
    Thread

    Black Box X32 Remember Machine Coordinates after reopening COM port

    Hello, I am a new to grblHAL motion control and am attempting to replicate some of the functionality of the openbuilds software in python as part...
    Thread by: Isaiah Baker, Jun 22, 2023, 5 replies, in forum: Control Software
  17. Jayar Bass
    Thread

    MIDI controller as manual jog/button controls?

    Is there any way you could use a midi controller, map knobs to axis controls, faders to feed rate/spindle rpm controls, buttons to home/zero axis...
    Thread by: Jayar Bass, Apr 5, 2023, 3 replies, in forum: Concepts and Ideas
  18. Andrew Catalanotto
    Thread

    Minimum Stepper Speed w/BlackBox X32

    I am trying to achieve stepper speeds between 1 and 100 mm/hour using the BlackBox 32 and a nema23 stepper motor. I contacted open builds and they...
    Thread by: Andrew Catalanotto, Mar 31, 2023, 5 replies, in forum: General Talk
  19. Ankit Kumar
    Thread

    GRBL: Need to run gcode between two homing cycles

    Hi, I am using grbl to control two different axes (X and Z) and want to run a piece of gcode after the X-homing cycle but before the Z-homing...
    Thread by: Ankit Kumar, Nov 19, 2022, 15 replies, in forum: Controller Boards
  20. Francesco Bravi
    Thread

    Grbl problems from Italy

    Hello everyone, my name is Francesco Bravi and I am writing to you from Italy. First of all I wanted to introduce myself and share with you what I...
    Thread by: Francesco Bravi, Sep 10, 2022, 5 replies, in forum: General Talk
Showing results 1 to 20 of 97
Page 1 of 5
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice