Welcome to Our Community

Some features disabled for guests. Register Today.

1500 x 1500 mm OpenBuild CNC

Discussion in 'CNC Mills/Routers' started by ACASTELLINI, Apr 2, 2016.

  1. ACASTELLINI

    Builder

    Joined:
    Apr 2, 2016
    Messages:
    3
    Likes Received:
    0
  2. ACASTELLINI

    Builder

    Joined:
    Apr 2, 2016
    Messages:
    3
    Likes Received:
    0
    Hello,

    I have around 1.5 mm (0,039 inch) less than the desired measurement.
    And this for a piece of 100 mm (3,94 inch) as for a piece of 1000 mm (39,37 inch) .

    Have you ever had this problem?

    Thanks in advance

    Adrien
     

    Attached Files:

  3. Giarc

    Giarc OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jan 24, 2015
    Messages:
    3,018
    Likes Received:
    1,688
    Sorry I can't help with your problem, but I have a question regarding your Makita router mount. Is that just a 65mm mount for the Chinese spindles? I plan to use a Makita, but I don't have easy access to 3d printer to make a shim so I thought I would order a mount designed for a water cooled spindle. Thanks.
     
  4. Giarc

    Giarc OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jan 24, 2015
    Messages:
    3,018
    Likes Received:
    1,688
    Thanks for the information
     
  5. Steve Fox

    Steve Fox Well-Known
    Builder

    Joined:
    Feb 22, 2015
    Messages:
    129
    Likes Received:
    21
    If you are saying that the pieces you are cutting are 1.5mm smaller than your desired measurement, there are several things that could cause this. The first is that the but you are using is larger than the published diameter. It could also be runout in your router.

    The fix is in the software. all the software packages I use allow an adjustment of the bit diameter and/or an offset adjustment for the part.

    In any event, this isn't unusual and can be corrected quite easily.

    Steve Fox
     
  6. Ronald van Arkel

    Staff Member Builder Resident Builder

    Joined:
    May 7, 2014
    Messages:
    472
    Likes Received:
    245
    It's not easy to get a belt driven 1220*1220 router work as they should be. Double belts, one in the track and one for the movement, are no luxery. Leveling the bed can be tricky and I recommend to use a transparent hose with water to level all the corners, sure, first having the corners square. Also, a NEMA17 for your Z-axis probably will be underpowered when you do 2.5D carving, but that's easy to change.

    Steve Fox is probably on your problem, a 1/4" tool can be off a bit so it will be 1/4" and a little, still, 0.75mm from center is a bit much.

    -Ronald
     
  7. GrayUK

    GrayUK Openbuilds Team Elder
    Staff Member Moderator Builder

    Joined:
    May 5, 2014
    Messages:
    1,668
    Likes Received:
    627
    Ronald. Forgot about the transparent hose and water level trick. :)
    Good one. :thumbsup:
    Thanks
    Gray
     
  8. Paruk

    Paruk Journeyman
    Builder

    Joined:
    Jul 13, 2014
    Messages:
    397
    Likes Received:
    149
    Hopelessly complicated, transparent hoses with water. ;-)

    Just take a wire (fishing stuff or so) span it from left front corner to right back corner and from left back corner to front right corner. All of course on top of the profiles. This way you will form a X of which the crossing should be exactly in the middle of your table and the wires at that crossing should only just kiss each other. Adjust the corner(s) that is (are) out of line until they just touch. Et voila! Your CNC is flat (the Y axis, that is).

    For squareness of the CNC, measure from the left front corner to the right back corner and compare that with a measurement from the right front to the left back corner. If they are the same, the frame is square. If not, adjust until both measurement are EXACT the same.

    Ronald is right about the double belts. I'm using it for about a year and have no accuracy problems (except for missing steps because of other reasons) whatsoever.

    Always measure your bits with a proper Vernier callipers (Mitutoyo is the best I think) and insert that value in your CAD and CAM programs. Do not assume the size, it will be off.

    Measure also the backlash. Videos of how to are al over Youtube.

    If you do this all correct, and some extra checking here and there, your Ox will be as accurate as can be for such a machine. I have about 0.05 to 0.1 accuracy (depending on temperature and moisture in the air, tropics you know).
     
    GrayUK likes this.
  9. GrayUK

    GrayUK Openbuilds Team Elder
    Staff Member Moderator Builder

    Joined:
    May 5, 2014
    Messages:
    1,668
    Likes Received:
    627
    I like the centre crossing point! :thumbsup:
     
  10. Paruk

    Paruk Journeyman
    Builder

    Joined:
    Jul 13, 2014
    Messages:
    397
    Likes Received:
    149
    Me too, Gray!;)

    About the bits, I was not complete. Only described the first part of it. After measuring the bit size for a first cut, you then measure the real life cut of that bit in your router to get the true size of the cut. That way you will also account for runout of your router and other minor in-accuracies. The width of the cut divided by 2 is your true tool radius. Use that value in your CAD and CAM software.
     
    GrayUK likes this.

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice