Welcome to Our Community

Some features disabled for guests. Register Today.

C-Beam CNC (1st cnc build!)

Discussion in 'CNC Mills/Routers' started by hasemar, Jun 28, 2016.

  1. hasemar

    hasemar New
    Builder

    Joined:
    Dec 11, 2015
    Messages:
    10
    Likes Received:
    9
    hasemar published a new build:

    Read more about this build...
     
  2. Kyo

    Kyo Veteran
    Staff Member Builder Resident Builder

    Joined:
    Feb 27, 2014
    Messages:
    673
    Likes Received:
    702
    Nice build :thumbsup: that is pretty much the same setup as my c-beam machine; even down to Pi 2 controller and drivers. It has been running great!
     
  3. Mark Carew

    Mark Carew OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jun 28, 2013
    Messages:
    2,760
    Likes Received:
    2,443
  4. Sonny Lowe

    Sonny Lowe Journeyman
    Staff Member Builder Resident Builder

    Joined:
    Nov 11, 2015
    Messages:
    143
    Likes Received:
    158
    Ryan,

    Love the build!!! Although I've not build my first CNC Machine YET :) I have two of THESE beauties and a Pi3 just waiting in the wings. I'll be following your build and the discussions with Kyo to lessen the confusions and frustration when I do get there ;-)

    Keep up the great work!!!

    Sonny
     
  5. hasemar

    hasemar New
    Builder

    Joined:
    Dec 11, 2015
    Messages:
    10
    Likes Received:
    9
    Thanks all, this site and its members have been a tremendous help!

    Future plans:
    actually cut something
    Fab cover over terminal blocks and wiring
    install limit switches for homing.
    build platform stablizers
    increase z axis rizers
     
  6. hasemar

    hasemar New
    Builder

    Joined:
    Dec 11, 2015
    Messages:
    10
    Likes Received:
    9
    Update:
    I made a successful run!
    Using a sharpie still. I created a text part in Solidworks and used HSM Express which is a solidworks CAM plug in. The post processor supports grbl but I noticed that it tries to use M30 which grbl does not support. It didnt affect the run though since M30 is an ending program code.

    At first the c-beam ran the but the lettering was backwards. It looked fine in the controller though. After some digging I figured out that I needed to invert the x axis in grbl ($3=2) . I ran it again and it fixed the problem.

    Almost ready to cut something. 2016-06-28 22.32.17.jpg
     
    Inis, GrayUK and Kyo like this.
  7. Kyo

    Kyo Veteran
    Staff Member Builder Resident Builder

    Joined:
    Feb 27, 2014
    Messages:
    673
    Likes Received:
    702
    Very nice! It is always exciting when you have your first successful run. I look forward to seeing what kind of projects you create with your cnc. :thumbsup:
     
  8. Sonny Lowe

    Sonny Lowe Journeyman
    Staff Member Builder Resident Builder

    Joined:
    Nov 11, 2015
    Messages:
    143
    Likes Received:
    158
    Congrats on your first run...very cool :cool:
     
  9. hasemar

    hasemar New
    Builder

    Joined:
    Dec 11, 2015
    Messages:
    10
    Likes Received:
    9
  10. Kyo

    Kyo Veteran
    Staff Member Builder Resident Builder

    Joined:
    Feb 27, 2014
    Messages:
    673
    Likes Received:
    702
    Looking Good :thumbsup:
     

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice