Welcome to Our Community

Some features disabled for guests. Register Today.

I rushed in and now I need help

Discussion in 'General Electronics' started by Christian Price, Dec 19, 2021.

  1. Christian Price

    Builder

    Joined:
    Dec 18, 2021
    Messages:
    5
    Likes Received:
    0
    Hello,
    Im completely new to cnc's but I saw a few cnc woodcraft videos and I started building a custom cnc but now I'm dead in the water. Im using the Blackbox controller and Control software which has let me move the x,x, and z but I can't control the spindle from the g code sender or vector. I purchased a spindle and vfd combo off Amazon but I don't know enough about electronic wiring or adjusting the software codes and settings. I do have power to the vfd and spindle enough to manually operate it but I don't know how to wire it to the controller.
    Are there videos or posts on how to wire up cnc electronics and adjusting whatever settings I need to? I've spent alot of time and money and I need to make this start to work for me. I need to learn what I don't know. Thank you in advance for your time and comments.

    Jiangshu Deoder Elwctric Co,. Ltd
    H100 Series mini inverter
    • Variable Frequence Drive: Power: 2.2 KW,Input Voltage: 220V,Output Voltage: 220V,Input Phase: 1 Phase,Output Phase: 3 Phase,Input Frequency: 50 Hz,Output Frequency: 0-400 Hz,Output Current: 25A
     
  2. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    14,945
    Likes Received:
    4,297
  3. Christian Price

    Builder

    Joined:
    Dec 18, 2021
    Messages:
    5
    Likes Received:
    0
     
  4. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    14,945
    Likes Received:
    4,297
    You can absolutely run manually if that's fine with you. Just a matter of convenience :)
     
  5. Christian Price

    Builder

    Joined:
    Dec 18, 2021
    Messages:
    5
    Likes Received:
    0
    Peter tha KS. I'm going to use these resources and I'll hopefully get it done right. I'll update you. Take care
     
  6. Giarc

    Giarc OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jan 24, 2015
    Messages:
    3,008
    Likes Received:
    1,676
    One nice thing about manual control is you can easily change speeds during a cut. This may be helpful when you are first trying to figure out the correct feed rate and spindle speed. I have been using my CNC for years and I have always used manual. It came in handy recently when cutting a really old piece of oak salvaged from a piece of furniture. The grain was so dense that I had to quickly up the spindle speed because I could hear it struggling.

    They don't make oak like that anymore.;)
     
  7. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    14,945
    Likes Received:
    4,297
    OpenBuildsCONTROL has a tool speed override slider too, if you do connect the VFD, you still have RPM override available mid-job for dialing in speeds and feeds:

    upload_2021-12-20_23-43-9.png
     
    sharmstr likes this.
  8. Christian Price

    Builder

    Joined:
    Dec 18, 2021
    Messages:
    5
    Likes Received:
    0
    Sharmstr
    Thanks for the advice. I was think that would be a benefit.
     
  9. Christian Price

    Builder

    Joined:
    Dec 18, 2021
    Messages:
    5
    Likes Received:
    0
    Thanks I'll try that so I'm not overwhelmed.
     
  10. Giarc

    Giarc OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jan 24, 2015
    Messages:
    3,008
    Likes Received:
    1,676
    I am so used to just starting it up and observing for a minute and making any manual adjustments on the router I forgot about that option.
     
    sharmstr and Peter Van Der Walt like this.

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice