Welcome to Our Community

Some features disabled for guests. Register Today.

Torque Specs for Bolts/Screws

Discussion in 'General Talk' started by The Dude, Jan 18, 2014.

  1. The Dude

    The Dude Well-Known
    Builder

    Joined:
    Jan 2, 2014
    Messages:
    243
    Likes Received:
    103
    Does anyone know what torque should be applied to the screws when assembling these v-slot parts? I have some 45mm motor mounting bolts(m3)... some m5 tee nuts about 10mm... etc I know this may be a strange question but I paid all this money for a torque wrench so might as well use it and have all those parts locked tight together on the frames and motors.
     
  2. Mark Carew

    Mark Carew OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jun 28, 2013
    Messages:
    2,759
    Likes Received:
    2,443
    That's a good question Dude and I am not completely sure of the answer, but I am interested if you are able to find out. It would be nice to pass it along if someone else has this question down the road.
     
  3. Al Hollaway

    Builder

    Joined:
    Dec 8, 2013
    Messages:
    2
    Likes Received:
    1
    Torque values chart http://www.holo-krome.com/pdf/torquedatachart.pdf
     
    Mark Carew likes this.
  4. Mark Carew

    Mark Carew OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jun 28, 2013
    Messages:
    2,759
    Likes Received:
    2,443
    Thanks Al
     
  5. The Dude

    The Dude Well-Known
    Builder

    Joined:
    Jan 2, 2014
    Messages:
    243
    Likes Received:
    103
    Are the tee nuts steel? Are these torque ratings the max for the screws? Isn't there going to be deformation of the aluminum if you overtighten steel screws? Some of the screws go directly into the aluminium so they may strip if overtightened...
     
  6. Al Hollaway

    Builder

    Joined:
    Dec 8, 2013
    Messages:
    2
    Likes Received:
    1
    Valid points.
    New chart http://www.enfieldmotorcycles.com/forum/index.php?topic=10638.0

    IMO it's more likely you would strip threads by over torque than to deform the extrusion. YMMV.
     
  7. The Dude

    The Dude Well-Known
    Builder

    Joined:
    Jan 2, 2014
    Messages:
    243
    Likes Received:
    103
    Thank you! That's awesome. I'll post the data here in case that site goes down. Screw Torque ratings.jpg
     
    GrayUK and Mark Carew like this.
  8. joe.carson

    Builder

    Joined:
    Jul 16, 2014
    Messages:
    11
    Likes Received:
    1
  9. Joe Santarsiero

    Joe Santarsiero OB addict
    Staff Member Moderator Builder

    Joined:
    Oct 30, 2014
    Messages:
    902
    Likes Received:
    196
    Nice find.

    EDIT: Note that the recommended torque is the recommended torque for a minimum engagement of 1.5 times nominal bolt diameter. If your engagement length is less than 1.5 times the nom. dia. then do not use the recommended torque provided.
     
    #9 Joe Santarsiero, May 3, 2015
    Last edited: May 3, 2015
  10. joe.carson

    Builder

    Joined:
    Jul 16, 2014
    Messages:
    11
    Likes Received:
    1
    Hi Joe,
    thanks for your hint! If I understand right you can define the length of engagement and the material under "Mating Thread Data".
    Do you think that the results calculated for a length of engagement of less than the nominal bolt diameter are not accurate?
     
  11. Joe Santarsiero

    Joe Santarsiero OB addict
    Staff Member Moderator Builder

    Joined:
    Oct 30, 2014
    Messages:
    902
    Likes Received:
    196
    When you input a value less than 1.5times the bolt diameter you will get the same value as 1.5 times the bolt diameter.
    If you torqued to those figures there is a greater likelihood of thread tear out the thinner you go.
     
  12. Joe Santarsiero

    Joe Santarsiero OB addict
    Staff Member Moderator Builder

    Joined:
    Oct 30, 2014
    Messages:
    902
    Likes Received:
    196
    Here is an example:
    Same bolt. Different depths. The first is at .250 depth and there is a warning.
    The second is at the minimum recommended engagement depth. No warning. Same exact figures.
    Warning! It is highly recommended that a bolt's engagement length be at least 1.5 times its diameter.
    Application Data
    Major Bolt Diameter: 0.250 in
    Bolt Thread Pitch: 20
    Bolt Proof Strength: 44000 psi
    Recepticle Length: .250 in
    Recepticle Strength: 40000 psi
    Applied Tensile Load: 0 lb
    k Factor: 0.2

    Recommended Torque
    43.75 in-lb
    (3.646 ft-lb)
    (4.944 N-m)
    Resultant Tension:875.1 lb
    Maximum Torque
    58.34 in-lb
    (4.862 ft-lb)
    (6.592 N-m)
    Resultant Tension:1166.8 lb





    Application Data
    Major Bolt Diameter: 0.250 in
    Bolt Thread Pitch: 20
    Bolt Proof Strength: 44000 psi
    Recepticle Length: 0.375 in
    Recepticle Strength: 40000 psi
    Applied Tensile Load: 0 lb
    k Factor: 0.2

    Recommended Torque
    43.75 in-lb
    (3.646 ft-lb)
    (4.944 N-m)
    Resultant Tension:875.1 lb
    Maximum Torque
    58.34 in-lb
    (4.862 ft-lb)
    (6.592 N-m)
    Resultant Tension:1166.8 lb
     
  13. joe.carson

    Builder

    Joined:
    Jul 16, 2014
    Messages:
    11
    Likes Received:
    1
    Thanks for the explanation, now I got it!

    Joe
     
  14. fonebone83

    Builder

    Joined:
    Feb 22, 2016
    Messages:
    1
    Likes Received:
    1
    GrayUK likes this.

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice