The idea is to make a simple effective ventilator, studying the concept of using a simple push process with and actuator.

Fixed Gantry CNC with good accuracy and rigidity but for a higher price than the usual CNC's on the site.

A modified 1000x1000 Sphinx, with a built in vaccum table.

This is a modification I made to my Voxel Ox 3D Printer Z axis, which synchronizes the Z leadscrews via a shaft and helical gear transmission. It prevents the two Z leadscrew from getting out of adjustment relative to each other, and uses a single Z motor instead of two. This build is just documenting the specific changes I have made to the Z-axis, since the frame and other axes are still from the original Voxel Ox design.

Build a 2x72 Belt Grinder out of OpenBuilds V-Slots

Cartesian type 3d printer build

Z-Axis upgrade with linear rails, SFU1204 Ball Screw and full aluminium construction.

This build is specific to a furniture design I am trying to bring to market. My first attempt to build a machine. I have looked at other build submissions to help me figure out where I would like to start. The workable volume should 36" W x 6" D x 6" T. The goal is to become more comfortable with the electronics side of machines I enjoy using and also lower the cost of my product by reducing man hours in the manufacturing process. Yay!

This 1500mm tall Delta is a work in progress. The triangle corners are water jetted from 1" 6061 Aluminum, and are welded to 1" square tubing. The 1500mm OpenBuilds 20x20 V-Slot extrusions are held into the corner brackets by two stainless steel set screws per bracket. This printer will need to be reinforced with wall brackets due to the combination of height/materials.

v-slot linear actuator build.

Xl 2 axis foam cutter Eps Surfboard blanks Simple open concept but high production machine. Shape 3d case with open builds controller

Its the first build for me so its just the story of me attempting to build the kit and hopefully end up with something I can use. Hopefully without destroying anything or anyone.

A Miter Saw station built using a Dewalt Miter Saw Stand and V-Slot extrusions.

This will be a step by step record charting my successes and failures in my voyage of discovery while building a CNC router. Please excuse my English-English which may lose something in translation to American-English. I would be grateful for any advice during the build

This is an experiment to build a Linear Delta Printer using four towers instead of three. Primary reasons: 1. Build area is roughly cubic vs roughly cylindrical 2. Greater speed and precision from additional control provided by fourth tower. 3. Symmetric kinematics from even number of towers.

An OX Router I'd like to modify to improve the frame rigidity and resolve some alignment problems

I'm building a CNC router in my garage (almost finished!) and I'm keeping a video build log of the process in the hope it may be useful to others wanting to do the same. I don't have much in the way of fancy tools so expect a bit of innovation on the way!

This specific build page is a collection of screenshots sampling some of my initial SolidWorks design and pictures showing physical construction of the initial design. I will be creating individual build articles as I redesign, test, and implement new aspects of the printer.

Large scale delta robot using c-beam as the core frame component.

I have decided to buy and build the ooznest workbee screw driven cnc (1000x1000) and also decided to use some plates and extrusions from the ox cnc. I will never use two machines anyway and hoping to build a strong base for the workbee.

Core-XY build witha quad nozzle

Leveling Platform / Stand 3D Printers

This is my build of Niko's (gianakop) Egg Painter. Egg decorating is something many Christians do for Easter Sunday and the Easter (Paschal) Season that follows. This will be my initial use for the build, but also with minimal modification to be able to write/paint on other round objects like Christmas ornaments, coffee mugs, etc. Many people also decorate eggs for purely secular reasons.

In order to make some nice traveling video you need a slider .

To help cutting v-slots with hand saw

An OX clone with alternative parts.

This is a 1500 x 1500 Ox build

Large 10’x6’ vacuum table made from steel tubing and 1/4 inch steel plate

Initial design for my CNC mill\router based around C beams

I wanted to try a different way of operating the Z Axis so I setup a tower using 40x40. In the end it worked excellently and can easily print 60mm/s with 150mm/s travels. The coreXY is a very cool kinematic, and you can get some pretty great speed and accuracy. The main issue is the fact your Steps/mm are doubled, so the lower end motors don't like it at high speeds.

This started as an attempt to learn to weld and quickly took on a life of its own.

The process from my bought printer, to a custom home built machine

Simple design with a large build volume - 450x450x450

Contains a further modification to Creality's poor CR-10 design

I really like the 4th axis I purchased a few years back, but when I went looking for it again the suppliers who once carried it no longer do. Anyone know who makes it? Center hole receives collets. I own a ShopSmith so I am using a 5/8th rod and can mount it's chucks onto this machine. Also I like the use of the skateboard wheels, they are adjustable and one could use more sets over a longer axis. The Sherline z-axis is not my first choice, I just had a spare.

This build is to show what's possible as well with openBuilds! I use a single ArduinoMega and 5 separate stepper drivers (A4988). The LEDs are all NeoPixels. Collision 'detection' is all done within the code, so the endstops are only sensors I use in this build. I'm a self-employed video-artist and this is my first installation which just needs power and it runs (where I'm quite proud of). Normally my interactive installations take a long setup time, so this installation is a relief :)

This built is to convert an existing 500x500 C-Beam Machine into 1000x1000. Inspired by several builds including C-Beam Machine : (http://www.openbuilds.com/builds/c-beam%E2%84%A2-machine-plate-maker.2020/) and Gino's build : (http://www.openbuilds.com/builds/c-beam-gtc.3250/)

1000mm X 1000mm overhead cnc machine

A Controlbox for my CNC-Router, containing stepper-drivers, Planet-CNC MK3 Controller and a Controlpanel with joysticks.

Home Made CNC Router from Scrape

Trying to build a machine of atleast 4x4ft working area. Work is in progress, hope to finish it soon

This will be my first build ever! Looking forward to it , just gotta finish the new workshop first then I'm on it!

I like this design a lot. It's very stable, very strong and with the EX2 enhancements, it prints like a champ.

Theoretical Working area: 38" x 24" x 6" Actual Working Area: 31" x 23.6" x 4" Positioning Accuracy: about 0.01mm

This CNC Router is to 95% made of standard parts and almost all of them from the http://openbuildspartstore.com/.

An attempt is to be a Unified Modular Controller based on M10CUBE platform. For GRBLHAL and MARLINHAL applications. HAL porting is under way 1 - WIZnet Pico Clone W5100S-EVB-Pico 2 v- 6 X StepStick. Not sure about the sixth driver, (Pico pins limitation) . External connectors for larger drivers 3 - Opto - isolated spindle PWM. 4 - HMI 5 - I/O on diferent modules and Ethernet 10MBPS communication. Patches will be written to GRBLHAL for Ethernet I/Os (Interrupted).

Open build rovo 1000mm * 1000mm. (Rovo x ver) 20.06.2015 now in progress. rovo kit is the 10th product. 8th rovo 750,9 th rovo1000, 10th rovo x ver progress at the same time. 10th item is an aspect of 1000. It changes the size and z-axis has been up.

The OpenCase Mounting Kit makes wire management quick and easy!

This is my second Ox with a working area of 14" x 14" x 5" I wanted to build a small sturdy potable CNC router and this OxZilla has the nice upgrades !

A new design of my based on a couple different machines I have seen both on openbuilds and youtube. In the end will have a and X/Y workspace of 1250mm x 1000mm and a Z axis range of about 200mm.

Workbee 1510 screw driven build by MsDosFX.

This printer will leverage scrap pieces around the shop to fulfill a single print's needs. It will use a combination of 80/20, OpenBuilds, and 3D printed parts.

I just did my first Powder coat paint job on a Z Axis with 9inchs of travel for the DIY CNC Plasma Cutter, Mill Head, Router, Engraver, Laser Head, Water Jet Cutter Machine. 2 different Z Axis ride plates and a 80mm Router/Mill Head/Spindle clamp. Baked on finish in a old oven i had.

C-Beam inspired CnC Router (1000x750) Approx 90mm of Z travel

Hello. I build this 600 by 600 printer and hope to share it. I plan to sell custom builds with my website in the middle of this yeahr while making all parts accesibble online for replacements and own builds. My plan was to build a better and more accessible big volume 3d-printer as cheap as possible. I got some inspiration of the ender creality 3, the crazy-Print xyz 300 and the veho 600 tronxy which was simply not relaible and satisfying overal.

C-Beam Plate cutter with Raspberry Pi V3, Arduino Mega2560 and Camera. Remote login & operation via SSH with cnc.js server, mjpg server on the Pi.

long overdue overhaul of 1000 x 1000 machine

3d printed V-Slot Gantry Plate leveler.

An easy simple Tape Dispenser, spawned out of necessity, and shared for the fun of it...

This is my first attempt at building a spindle based CNC machine. The intention is to mill PCB boards and mill delrin blocks. The device was built with an Emergency Stop that actually cuts power to the spindle and motors. This is a post build write-up and consists of finished photo compilation and CAD renderings.

Work in Progress of a laser cutter design. Based on the CoreXY build from https://makerstore.com.au

Build Notes: Here are all the parts necessary to re-produce this design. Please note, all of the parts are either sourced through openbuilds or have been selected and printed from thingiverse.

This is a video were take a high level look at how I built up my version of a fully open source Motorized Camera Slider (OpenSlider)

To build a simple EggBot

I like combo machines, so I upgrade my 3D Printer with a Laser. It is a double head combination. The Laser is easy removable.

My Controls box to run my Workbee 1510 That was retrofitted with Lead Screws as well as Lineal Bearings. The stock electrical configuration was not enough, so here are the Measures that I took to not only make this machine Run again, but to have fun with it, and make this system be able to run any CNC I run in the future with the installed microcontroller.

The Mule is a 3-axis CNC inspired by the OX CNC by Mark Carew. This machine borrows the OX's sturdy frame and upgrades the X and Y linear actuators through the use of three 500mm lead screws (as opposed to the belt system of the OX). The result is an inexpensive, sturdy, and powerful design built for cutting tough materials such as aluminum.

My cnc update and rebuild.

This my version of a large no corners cut Delta.

Turning my prototypes into real objects, it will be required a great amount of drawings, A LOT. Therefore, against the ink costs raise price push me to think in a way to draw models, blueprints, etc. at very, VERY low cost. This is where my DrawBot was born

The Multi Z adds multiple Z axis to a LEAD CNC Machine allowing it to cut and carve 2 to 3 times the amount of projects in the tame it takes to make just one

Mostly for Mill work, and FDM 3D printing (mostly Nylonx). I'm currently in the process of adding some hardware for a project requiring lathe work. I've included a solidworks 2014 pack and go for those of you interested in the build. if you need another file type, just let me know and i can try to accommodate. This is a scratch build (electronics and hardware)... see photos. Everything is pretty close to industrial quality... Electronics too. I got sick of other COTS designs breaking down

Video on youtube: https://www.youtube.com/watch?v=vCTbLZ2_m-w&t=36s

Total belt drive GT2

A table top OpenBuilds MiniMill build. 48V 52mm spindle with ER11 collets.

this is my first attempt at a CNC Table

A quick and easy way to make a 3-way mitered corner using MakerLinks

A light 3D printer made of OpenBuilds hardware only

only 2 screws to hold down even bent sheet material and vaccum dust removal in one

A few mods on my Ooznest supplied Ox cnc Encountered a few minor issues along the way but now all sorted.

1000mm x 1000mm linear rails, double gantry, build in Process... more to come

A small business idea led us here, lets see where it will go.

Large floor or wall mounted plotter design.

This is my take on the Acro Laser system made from mostly salvaged, scrap, or leftover parts. I modified the plates in an attempt to maximize the cutting area and I wanted a lightweight adjustable Z axis.

This is a work in progress ACROS build with new legs and wire tracks.

A build of Schematix's Ox-Metal design, with a 0.8kw watercooled spindle.

I ordered the OpenBuilds MiniMill from the OpenBuilds Parts Store http://openbuildspartstore.com/ They were out of Motors and Electronics when I ordered so I had to source these items elsewhere. But it turned out well doing it this way.

We created an A1 ACRO Drawing robot specifically for the artist communities. It utilizes the popular ISO 'A series' paper sizes standards

A simple 3D printed dust shoe for the cnc router. 2 parts held together with magnets for easy bit changes.

Getting more height out of the !510

A DIY 3D printer. At beginning made from aluminium profiles, aluminium sheet and wood :)

This is a work in progress

Cheap, experimental Modification to Tevo Little Monster's bowden system for the extruder

I could not "tram" the spindle to the table. I found that the V Rails could not accurately be adjusted so the Gantry was equal distance from the spoilboard in multiple places.

Router for making plugs for composite part production, and for cutting CFRP.

I'm starting my first own build cnc machine which is inspired by routy and the ox. Were my goal was not to use the ox plates but use the standard plates available in the parts store for the design.

My first custom build, using vslot rails for Z and Y and 8mm rails for X. Currently printing parts for this using my Prusa I3. The build volume will be roughly 300mm^3, X and Y are belt driven with 8mm acme lead screws for Z. Will be uploading more info shortly as i continue to build the printer.

A C-Beam machine design, strengthened with extra brackets and plates. GRBL controlled, opto-isolated inputs, jogging box.

A stable CNC Router that allows me to cut and carve bigger Parts. The Machine is an original Build from Kyo's Sphinx CNC Machine. Thanks for the great Work and the Effort Kyo. Your Files and Lists helped me a lot to build that Sphinx 1x1m.

Build features include a double c-beam gantry (bonded & mechanically fastened), linear x rails, custom gantry end plates, a custom linear rail & ballscrew Z axis, and custom lead screw tensioning plates. The primary goal was to remove twist from the 1500mm gantry & stiffen the Z axis.