My version of the Mug Plotter designed by Teed http://edinburghhacklab.com/ . Also used the Eibotboard from the original eggbot from evilmadscientists http://shop.evilmadscientist.com/partsmenu/188-ebb A huge thanks to Hexitex for his brilliant Four jaw chuck http://www.thingiverse.com/thing:5791

This SphereBot is based on the EggBot which is an open-source art robot (drawbot) that can draw on spherical or egg-shaped objects.

Laser CNC, 60W, didn't have one yet... have to :) This build is a retrofit of a surgical laser into a CNC.

A CNC router designed to handle a 4'x8' sheet, for as close to $2000 as possible. The price barrier resulted in my choice to use timing belts rather than leadscrews or rack&pinion. Build List still being updated

The C-Beam Evolution is an evolving machine. The MkII is inspired by Kyo's C-Beam Spinx but currently uses my own design of plates made of 8mm acrylic (X-axis ends) and 6mm polycarbonate (Y axis ends). The plates were made on the MkI but I hope to be able to make 6mm aluminium plates on the MkII for the MkIII.

Hypothesis - Running CO2 laser tubes at high amperage may shoirten tube life in number of hours, but will be made up for by the increase in actual inches engraved/cut using the higher power. This is a long term experiment, so the build status will remain as "Build in progress" until the experiment has been completed.

v-slot linear actuator build.

2 1/2 axis CNC chassis. Convertible to plasma, 3D printer and welder. Currently used as router. Plotting table dim: X axis 620 mm, Y 650 mm, Z 100 mm. Created for teaching purposes, open source license, currently used for engraving ukiyo-e wood plates and printmaking

Building of a big open frame laser engraver.

A brief write up of the making of the FLSUN Delta Kit. This kit is based on an open source design. I had a need for a 3D printer without the desire to dive into another project, so a kit was the obvious way to go. I already have a delta printer in the works and so this is more of a stop gap in the interim.

CoreXY printer

A simple fixed dust shoe for your OX.

A build of Schematix's Ox-Metal design, with a 0.8kw watercooled spindle.

The original plan was to build a 3d printer with a 1200x1200 build platform with a 600mm build height. I was having issues getting ahold of a large enough borosilicate glass plate for the build so I decided to go for build height. I plan on using a smoothieboard for the controller. The build has currently slowed down. I was removing a broken drillbit from the linear rail mount, and it shattered and took out my eye. I am doing what I can when I can focus my eyes long enough for the build.

C-Beam Plate Maker with a larger size of the work area and electronics added.

Embarking on my first build and trying to start with a clean setup by creating an enclosure box for my controllers and power supply.

It all started after my prusa i3 build inspired me to experiment with resin 3D printers because I want to learn if they are worth it and if I can design my own printer.

Based on the work of Carl Feniak and his C-Bot. A robust Core XY style 3D printer that has a clean parallel belt implementation and whose dimensions are adaptable to meet builder's needs. The use of open builds V-slot and other open hardware make customization easy. Utilizing a 300x300 build plate this derivation utilizes three lead screws, synced to a single motor via gt2 belt

Aluminum-framed enclosure for TAZ 6 3d Printer made with Makerlink.

Delta printer designed in sketchup and includes an adjustable bed.

Quick overview of my build up for a vacuum former that is self contained, portable and fairly easy to build.

A quick and easy way to make a 3-way mitered corner using Corner Connectors

Design Change - Version 2.0 has a smaller foot print, custom gantry supports, and front and back covers. I will use standard V-Slot for gantry supports leaving me enough travel to manufacture the customer supports with this machine when completed. then update to final build. I also plan to install the controller into the front cover and power supply into the back cover. Should be nice and tidy.

A low cost and easy to build laser cutter based on 2.8w laser diode .

Just some repairs and upgrades to my drill press and mitre saw using c-beam.

Fully welded, fixed gantry CNC router, with chinese linear motion parts, in progress

Work in progress large volume CoreXY printer

While building my OX AI I found myself with left over v slot and thought to myself, what do I need that I can build using them? Well since I make a lot of my own PCB boards for projects I figured a micro PCB mill would fit the bill ;) With inspiration from the OX and OX AI I give you the Stinger V :)

Not much to say... Soundproofing box for noisy works... Build in MDF and 20 mm plexiglas. Very effective!!!

I made a cam slider prototype with adjustable rotation to get experience for my CNC milled slider in planing.

This CNC utilizes the C-BEAM extruded aluminum for the "X", "Y", and "Z" axis. The gantry will move similar to the OX along with the "Z" except I am incorporating the C-BEAM instead of the 20x60 V-RAIL. To make the system as strong as possible I am using two C-BEAM rails back to back. The "Y" axis will encompass two sets of roller on both side of the C-BEAM extruded rails for added strength. All of the plates for this were created using the C-BEAM machine I completed several month ago.

This will be an Aluminum OX build. Plates and all design credit goes to Mark from open builds. I may add my own touches but mainly this is to see how Aluminum plates perform

I will be attending the 2017 Midwest RepRap Festival (MRRF) with a small team of printer enthusiasts with a goal to fully assemble a Core-XY D-bot onsite during the event. This is our first attempt at building a D-bot and we will be learning things as we go. Our hope is to have the entire machine assembled, wired, and functional (at least to the setup and testing phase) before the end of the show. Please attend and watch us in person or visit our feed channel during/after the event.

The aim of this build is to have a CNC that can cut a FULL sheet of wood when I need it to, but also shrink down and cut smaller sheets the rest of the time. The prototype is based on an OX cnc but soon it will be completely custom using Openbuilds Parts

A humble first time attempt at building a 3d printer from scratch

In Greek mythology, Talos (/ˈteɪlɒs/;[1] Greek: Τάλως, Talōs) was a giant man of bronze made by Hephaestus (the Greek god of fire, metalworking, craftsmen and blacksmiths) who protected Europa in Crete from pirates and invaders. He circled the island's shores three times daily.

Total belt drive GT2

Long duration , high intensity SCUBA dive light using Li-Po 18650 batteries and advanced circuitry.

This build is inspired by the Lulzbot Taz printers and makes use of the new OpenBuilds C-Beam

This is a handy machine to assemble touch sensors into display frame.

One of my first projects might be cutting proper plates.

My first project build. Concept build to use an existing 7.5 ft tall server rack as the frame. This ptoject may never be completed.

Cooling system for water cooled spindle.

This build is for a testing rig to use while testing out different controller boards and CAM software for milling and routing. It is in the early stages, planning is complete, parts are ordered. Awaiting parts delivery to start build. Please not the BOM only covers parts from the OpenBuilds part store. I will be posting the other required items very shortly.

I need a large build plate without spending 10-20k for a "store" built printer.

This is a work in progress

Open the build will create open and sharing. 오픈빌드는 만들고 오픈하고 공유합니다.

C-beam based CNC router using mostly openbuilds parts.

This is my OX. There are many like it, but this one is mine. My OX is my best friend. It is my life. I must master it as I must master my life.....

CoreXY Table with Symmetric Lead Screw Z axis, Build volume: 293mm x 290.75mm x 223.83mm

in construction ! chassis vslot 80x20 & 20x20 & 60x80 (Z) home made plates with whells polycarbonate build volume environ, 750x300x200 2 ed3d v6 volcano nozzles 0.8mm & 0.6 + titan extrudeurs rumba bord + auto levelling ip camera home made heat bed aluminium 5mm + glass + heat air chamber 6 doors plexiglass......

The Routy GT2 300 BSX CNC Router is a Low Cost CNC build. It performs the same as the larger Routy's from OpenBuilds but doesn't break the bank!

Modular easy to adjust scale of the entire build Tablet/LCD monitor SLA 3d Printer.

ELECTRONICS - ARDUINO Mega 2560 + RAMPS 1.4 + power supply 12V - Leadshine DM 5042 external driver + Power supply 36V + NEMA 23 stepper motor SOFTWARE - Repetier Host to communicate with the Ramps - ARDUINO to upload the firmware (Marlin) MECANIC - V-Slots rails 40x40 + home-made plates - everything goes fine on the side of the build

DIY Pano Head

Epoxy dispenser, 2nd one, first one works great. Uses HMI to allow for operator to pull up files for different jobs. 9 prox sensors, Eot and home on all 3 axis. High quality nema23 motors with intergrated drives from applied motion. Uses programmable router for drives.

wanted large work area for laser etch/cuts more than spindle work.

A simple made hideaway for ugly electronics

Open source clock movement stand

A modified OX based on Aluminum plates cut on a waterjet. Some new ideas and additions from other builds are included.

I have been working on this project for something like 3 years on and off, sometimes leaving it for a few months. Now I really want to finish it. For me, the mechanical part was the easy (though long) part because I get to use about 17 CNC machines and MasterCAM and I am a machinist. The hard part is the electronics part. Had a few problems getting Windows to communicate to the X5 Mini via the USB cable but found something on the Smoothie forum and got the machine moving.

I have parts that are apparently not suited to a cnc router or a 3d printer. I am still trying to figure out what to make out of what I have,

This is going to be a more or less detailed how to build BetterBot. Pictures and more (decent) text are to be added.

Please, look over my build and make any recommendations you can think of! I haven't figured out how long my arms need to be yet. Nor have I done any shopping around to find better prices...

This machine is fantastic. Teamed up with Fusion 360, Inkscape, and GrblPanel, I'm well on my way towards making at least one Christmas gift this year. I had some frustrating times during the build, mainly with getting everything to go together square, but overall it was fun. I can see that I'm going to need to be a bit creative in order to max out the work area for this machine so that I can produce the product I bought it for, but it will be able to do so much more for me as well.

Making a bellows to cover a C-beam to prevent swarf from gumming up the works.

This 1500mm tall Delta is a work in progress. The triangle corners are water jetted from 1" 6061 Aluminum, and are welded to 1" square tubing. The 1500mm OpenBuilds 20x20 V-Slot extrusions are held into the corner brackets by two stainless steel set screws per bracket. This printer will need to be reinforced with wall brackets due to the combination of height/materials.

Homemade plasma cnc

1000mm x 750mm OX with some planned enhancements. My first venture into CNC.

This is a 1500 X 1500 Stainless OX kit build, by a cnc novice. It is the first cnc machine i have ovned and build I got this kit from http://makersupplies.dk/20-ox-cnc-kits

A new mini version of the http://openbuilds.com/builds/openbuilds-freeburn-1-v-slot-co2-laser-60-100w.1001/ FreeBurn CO2 Lasercutter

We wanted to create a rapid prototyping machine with excellent 3D printing, laser cutting and engraving, and light CNC router work capabilities.

Started my build of a large Sphinx style cnc Router. I wanted one to handle the Dollar Tree Foam Board (DTFB) so I am making this to handle 2' X 3'. This is my first endeavor for a CNC so I am learning as I go but there is one thing for sure.

This is my journey on building a rack and pinion Ox variant called the F-117 CNC.

Initial design for my CNC mill\router based around C beams

Dual X-Carriage CoreXY. Not impossible, but probably the only one. Use the link to Thingiverse "Hlidskjalf" for parts and downloads.

PPR = Portable Plasma/Router. A ~30x30"work area with leadscrews. Work surface is below support members. Can be placed ONTO cutting surface.

C-Beam XL with v-slot aluminum bed for fixturing.

Kind of hard to see in this pic now lining up drive s and finishing framework

This is a simpel build of a Linear rail for the Dobot Magician.

Pretty much a straight OPENBUILDS OX that slowly getting some modifications.

My CNC project

Its the first build for me so its just the story of me attempting to build the kit and hopefully end up with something I can use. Hopefully without destroying anything or anyone.

CNC OX 1500X3000

This is my first major project.

i wanted to use both the ox and the C beam C beam for the gantry because its stronger i also made the gantry 20 mm higher so i can cut thinker material i will maybe later go to rack& pinion on the 1500 mm Y axes also instead of the V wheels i will maybe go to hiwin in the furture

Using criticall OpenBuilds components to upgrade the rigidity and reliability of an X-Carve 1000mm build.

MY experience as a first time introduction to the CNC world!

This is a pure cbeam build to maximize envelope and rigidity. All the parts used are available from open builds.

This is the story of my experience building a 1000 x 750mm OOZNest OX CNC router

ive got most of the wire harness made up too im using Chinese electronics for now I will upgrade later when this thing makes me some cash lol im using a ibm think center to case to hold my electronics ive got a 25' parallel cable to put some distance between the table and the computer

This Project is meant to teach introductory robotics and arduino styled micro-controllers to HS and MS students.

This is my own modified version of the D-Bot printer. I wanted to spec this printer to be able to print exotic materials at high accuracy with little to no compromises and maximum reliability.

Sheethexapod works with basic mechanims as direct metal-metal links and joints, all movements can be done by a rc servomotor in this case towerpro model.

You are about to read the evolution of my 3d Printer build.

i always make laser cutting machine, but when i see openbuilds, this can make more cheap gantry for make laser cutting.

Modded Plate maker with: Smoothiebrainz board and DQ542MA SN04 Endstops Modded Z axis Aluminium build plate and renforced Y axis Dust shoe

The X/Y table system is a great starting point for many CNC projects giving you the ability to move an object on the X and Y axis in a simple compact style.

This is a stool, designed in 18mm wood for a cnc router, it's easily scaleable to different wood-thicknesses, in 18mm wood it takes up 1200*1200mm. It can be assembled without screws, nails or glue and can therefore also be easily disassembled.

Low cost Laser Engraver build using all off-the-shelf components.