First build of CNC OX for the purpose of using it for Guitar building to take a lot of the muscle work out so I can concentrate on the finer details.

1000mm x 1500mm OX router using Openbuilds parts and plates by Chris Laidlaw

I just did my first Powder coat paint job on a Z Axis with 9inchs of travel for the DIY CNC Plasma Cutter, Mill Head, Router, Engraver, Laser Head, Water Jet Cutter Machine. 2 different Z Axis ride plates and a 80mm Router/Mill Head/Spindle clamp. Baked on finish in a old oven i had.

This is a cartesian CNC Router build that is based off the OX CNC build by Mark Carew. I am using Spark Concepts CNC xPro controller board and their 400w spindle kit.

Designed from the ground up as a low cost, highly scalable delta printer. This printer has been built as small as carry on luggage size, up to an 18in wide print surface and is capable of larger. Approximate cost is low to mid $500 range start to finish, including electronics for a basic model.

only 2 screws to hold down even bent sheet material and vaccum dust removal in one

My version a Cartesian style 3d printer, an attempt to eliminate frame vibration and movement and to use up materials left over from other projects.

A 3-axis flying gantry (4'x4') mechanical kit is assembled. A 3D printer is used to make cable chain for tidy and cheap wire management. A BeagleBone Black development platform with Machinekit software (LinuxCNC) is configured to control a Xylotex motor driver box connected to an Openbuilds Ox direct-drive pulley and belt motion system. A vacuum dust-collection system is designed, CNC-routed and installed. A steel table is made to mount the table onto.

OpenRail attached to a 19" rackmount 15U box.

PVC foam Core frame made from a Delta facet display. a curb find while walking home.

Powder coated multi CNC Z Axis plasma adapter with Proximity sensor. . It can also hold a 80mm Router head/Spindle as seen in my router build.

I have constructed frame out of 1 1/2" square tubing. Have my Y aces mounted. and awaiting parts.

This build is to show what's possible as well with openBuilds! I use a single ArduinoMega and 5 separate stepper drivers (A4988). The LEDs are all NeoPixels. Collision 'detection' is all done within the code, so the endstops are only sensors I use in this build. I'm a self-employed video-artist and this is my first installation which just needs power and it runs (where I'm quite proud of). Normally my interactive installations take a long setup time, so this installation is a relief :)

In the expo projects during the second year of engineering students. the project group who made this rapport made a laser cutter for the students of Fontys Hogeschool Engineering to use this machine for creating parts for their projects. The goal of Project Laser Cutter is to build a laser cutter, which is safe and can be used within the school. Also it has to be able to cut through 10 millimetres thick acrylic material or 10 millimetres thick plywood. This project will follow the V-model. This

Open source 3D printer with very powerful heated bed and light weight x axis design. Full source repository can be found here: https://github.com/a-drizzle/Printer1

My large printer design. 400mm build plate, ~1000mm build height. Most of structure is 8020 but the sliders are V-Rail

This slider uses an 500mm OpenBuilds C-beam and the design is such that the effective length of the slider is slightly less then twice the length of the C-Beam. It can be used both motorized or not.

A CNC platform designed with swapable heads to do laser engraving/etching/cutting, routing and milling, as well as 3D printing.

UltiBots LLC designs and packages DeltaBot 3D printers using quality components. Our kits are V-Slot based. Print results are impressive. The Metal MagBall Carriage was designed to be ridged, compact, and simple.

Short description of my assembly and use of the C-Beam bundle from the Open Builds Part Store.

Per the special notes its a variant of the C-Beam, Machine.... I have noticed that alot of people build a CNC router to cut parts for other larger CNC machines.. eg Delta Printers etc....plus this will enable me to cut parts for model RC plans UAV's etc...

I'm starting with the c-beam bundle, and I hope to end up with a pretty useful little platemaker/shallow relief carver. I'm hoping to discover how accurate and efficient it can be.

Just an idea right now but will attempt a prototype in the near future. Not sure if this has been tried before or not.....

3d printed V-Slot Gantry Plate leveler.

A 3D Scanning Station

C-Beam basic package doubled in size.

This a redesign of the Folger-Tech Y-Carriage using the Solid V-Wheels, Ball Bearings, the V-Slot Rail System.

A completely belt driven cartesian design with a center mounted X motor. This is a very compact, rugged design.

Using the Routy290 build and an awful lot of help from puntoMX, this machine has been expanded in the X and Y axis. My first build, I'm learning a lot about all of this. I've had to disassemble parts of this thing many times due to forgetfulness, but that's ok. Also, I've forgotten to take constant pictures throughout the build.

1500 x 1500 mm OpenBuild CNC

An easy simple Tape Dispenser, spawned out of necessity, and shared for the fun of it...

In short...this was a fun project.

This build is intended as a light alternative to the Dremel rotary tool.

Dewalt 611 Router mount for mounting onto 20x60 v-slot

www.cncforeveryone.com. the Duck is something that i think would be helpful in my shop since we already do cold casting.

C-Beam Plate maker for My OX!

Document my OX build process. I will also be sharing SolidWorks parts files & assemblies.

My own Design (not an OX Derivative) using standard Parts.

I am in the design phase of my CNC. I would like to thank everyone who has placed resources on the site. I am using it to the up most! I will update as I continue the design and share my progress.

Optical home and limit switches for cnc, 3D printers, laser cutters, etc.

This is a big 609 x 609 x 914 3d pritner with exchangable hot ends and extruders.

Here is the consolidation of my woodworking shop, a CNC Router!

What I want to build is a unit to: rout wood, plastic and occasional aluminium . to be able to swap cutters. i.e. drragknife, laser, router, drill

Square shaped OX for doing general purpose engraving and cutting into wood, acrylic, and aluminum.

Using a Raspberry Pi, Arduino and a Protoneer CNC Shield to create an Open Source CNC router controller. It will be equipped with a touch screen to control the on board processor. The touch screen will run a user interface that has buttons for added functionality. There will be a camera for monitoring progress from inside my office. The control box will also feature a way to power the vacuum and spindle/router . I will also be able to monitor room temp as well as Pi CPU temps and averages.

A Laut3k derivative that goes for volume and large number of print materials at the same time. Using OpenBuild linear motion systems to get away from belt drives.

Here it is my intention to show what was involved in adding a CO2 laser to my existing CNC machine.

An easy Epic Win for novice engineers new to the RepRap project www.3distributed.com

Build Start to begin Feb 1st.

This is Fina; My Lautr3k inspired build.

It took me 18 long nights to build it

This is the first project that I would like to share with you. I know the build looks familiar and it is; it’s based on kram242´s Routy. Work area is 300*500*55 mm and is NEMA17/GT2 belt driven.

Out with the Old in with the New. Trying to build a nice clean setup that myself and my sons can use and enjoy.

The Mule is a 3-axis CNC inspired by the OX CNC by Mark Carew. This machine borrows the OX's sturdy frame and upgrades the X and Y linear actuators through the use of three 500mm lead screws (as opposed to the belt system of the OX). The result is an inexpensive, sturdy, and powerful design built for cutting tough materials such as aluminum.

[EN] Build of my Multiple OX CNC. It's goal is to run in 2 differents modes : router and 3D printer modes. The router mode will allows the use of a laser diode or a standard spindle. [FR] Construction d'une CNC basée sur l'OX pour des usages multiples. Deux modes principaux sont prévus : l'impression 3D et l'usinage via une defonceuses. Le mode usinage permettra à l'avenir de placerune tête laser pour effectuer quelques gravures simples. Une version française : http://kermareg.be/?page_id=103

A simple 3D printed dust shoe for the cnc router. 2 parts held together with magnets for easy bit changes.

An OX clone with alternative parts.

The Ronin OX is a dedicated fiber composite milling machine. I give a complete in-depth article on how to take a nearly stock OX build and easily turn it into something that can mill carbon fiber and G10 plate effectively and quickly.

One meter square. Short and stout.... reminds me of a Sumo Wrestler. A temporary and adjustable configuration I have devised to cut my own plates. I have kicked around ideas for about a year and the C-Beam extrusion has made this attempt to realize my ideas irresistible. This is just one step towards bigger and better things!

I'm starting my first own build cnc machine which is inspired by routy and the ox. Were my goal was not to use the ox plates but use the standard plates available in the parts store for the design.

I want build a frame that is as sturdy as possibility while at the same time keeping it as compact as possible. working area will be approx 1200mm x 600mm

This is my second Ox with a working area of 14" x 14" x 5" I wanted to build a small sturdy potable CNC router and this OxZilla has the nice upgrades !

Use of V-Slot for frame and rails with option to use identical 500mm uncut lengths: 8 * 20x60 x 500mm 8 * 20x40 x 500mm 7 * 20x20 x 500mm (2 cut into four identical 125mm pieces for filament holders) Use of uncut 500mm rails obtained through use of 12 joining plates for use as spacers. Alternate approach is to trim two 20x40 and 1 20x20 rail by 6-8mm each. Build volume ~400mm cubed (with dual extruders). Use of only openbuilds components! Currently in design phase...

This 3D Printer is made to provide the most accurate results with the least amount of investment. This Printer is being designed to allow the common user to own a very accurate piece of machinery.

This is my story about my need for a CNC router on a budget that wound up in the $5K range !!! but I have a good belt drive Ox

My very first attempt at a CNC build. Based on the OpenBuilds C-Beam Machine, small tweaks will be made to tailor it for my goals: machining G10, aluminum & some carbon fiber for use with multirotor and motorcycle parts. I am looking forward to the day when I am comfortable enough to bring the ideas in my head to the tip of the end mill in a smooth fashion...

This build is very straight forward. The design is simple. There is a great support community for Delta 3D printers.

OX 1500mm x 1500mm w/1.5Kw Water Cooled Spindle & VFD ran by a Gecko G540 & Mach3

A System of 3d printed parts to use along with your projects aluminum extrusion to cut your pieces of v-slot to length manually.

This build is made by students from Fontys Hogescholen Eindhoven, department Engineering. Every quarter a new group continues the work of the previous group. We have been working on the project since september 2015, and as it is a work in progress, a lot will be added later. The first months have mainly been about designing and building an XY-table on which later all the electronic components will be added and the laser.

C-Beam build using the small C-Beam gantry plates only.

This is a Dual X-axis platform.

Mega-sized Taz machine. Supports many tools (extrusion, laser, mill, etc) simultaneously.

C-Beam Router using 1500mm lengths, 48x48" build area, and rack and pinion movement.

Dual extruder 3D printer and laser cutter.

Fascinated for some time by 3D Printing. Now, after studying countless forum posts, blogs and similiar stuff, i want to Start with my own build. Maybe a bit much but usually i thrive with the challenge.

The QuadRap 3D printer version based on OpenBuilds wheels. Born in https://plus.google.com/u/0/communities/103539262895202172380

Most of the way through the build, hopefully soon I will have it running

Here is a nice little simple build that will help to free up some extra space on your work bench. If your like me you need all the room on your work station you can use, so this is great to have.

The STEAM Crane 3d printer uses the new C-Beam linear rail. It is being developed for an after school / summer camp program for kids. All of the electronics are housed in the base and the wiring is routed down the channels of the c-beam. This is done to contain as much of the loose wiring as possible, hopefully keeping it safer for kids.

A fully aluminium printer made from off the shelf components, no printed parts.

My build of the OX kit from SMW3D.com

Mag arm deltabot with laser cut carriages and connectors.

Someone donated a E3D Volcano to me (http://e3d-online.com/Volcano/V6-VOLCANO-POWER-PACK-175-UNIVERSAL-24V) and with a super hotend like that, it feels like a waste to stick it into a small 3D printer. So I decided I want a 320x220mm (XY) machine, 200mm Z is plenty for me

Planning my build, just looking for design input at the moment. I definitely want a slave X axis. I am potentially going to go with one of the 1500W Chinese water cooled spindles.

I ran across the OX and knew it was the one I wanted to build. Some of the things I wanted to include was make it bigger and a little more solid than what the original plans called for. So here is where I am at so far. It will have a cutting area of 48" x 48". The waste board support frame will have more support rails. The Y axis will have (3) 20mm x 60mm rails instead of the original (2) that is called for. 1/4" aluminum OX plates. And a few more odds and ends.

An X-Y Stage created from two self contained acme screw linear actuators. This build was published as an example of how many of the OpenBuilds Parts can be used.

Another modification on the OX

Small Form factor based 3 axis Gantry style mill, Removeable mechanical module. Removable Electronics. with a removable machine pallet, for automation.

Routy cnc upgrade.

I am very grateful to Mark Carew with passion and imagination. Therefore, the machine is good, but making the website there too daedanhaeseo The end of the same either way to invisible homework. Thank you for allowing openbuilds team submitted to the challenge once again for those with a passion that I feel like in Korea, I want to be a great help.

My attempt at planning out my own CNC router

Build the efficient and reliable all metal structure 3D Printer. Improved significantly with new concepts for printers. Great quality and up to 400 mm/s print speed (very fast). Built with heated bed, hybrid bowden suspended extruder, and counterweight (tested printing 21 hours straight with no motors hot). Optional smart controller for computerless printing. Print any kind of thermoplastic.

Small CNC - made with some custom lasercut+bent sheetmetal parts + Openbuilds V Slot

LASER ENGRAVING DIY 60 WATT

The frame is made from all open builds parts, add the rubber feet and pads for the glass. The glass is clear 12" x 16" x 1/4" with a polished edge. A light basket slides on the countertop.

Phlatprinter MKII Foam Cutting Machine

Creating a CNC mitre (45°) cutter, for picture frame cutting. Starting with an OX, but inverting various parts and adding a material table, with a stepper-controlled measuring guide.

This build is very straight forward. The design is simple. There is a great support community for Delta 3D printers.

Yet Another Openbuilds Router, my version :-)