First build of CNC OX for the purpose of using it for Guitar building to take a lot of the muscle work out so I can concentrate on the finer details.

I just did my first Powder coat paint job on a Z Axis with 9inchs of travel for the DIY CNC Plasma Cutter, Mill Head, Router, Engraver, Laser Head, Water Jet Cutter Machine. 2 different Z Axis ride plates and a 80mm Router/Mill Head/Spindle clamp. Baked on finish in a old oven i had.

3.8 W laser add-on for C-Beam machine. Can easily be swapped with the router.

Designed from the ground up as a low cost, highly scalable delta printer. This printer has been built as small as carry on luggage size, up to an 18in wide print surface and is capable of larger. Approximate cost is low to mid $500 range start to finish, including electronics for a basic model.

My version a Cartesian style 3d printer, an attempt to eliminate frame vibration and movement and to use up materials left over from other projects.

A 3-axis flying gantry (4'x4') mechanical kit is assembled. A 3D printer is used to make cable chain for tidy and cheap wire management. A BeagleBone Black development platform with Machinekit software (LinuxCNC) is configured to control a Xylotex motor driver box connected to an Openbuilds Ox direct-drive pulley and belt motion system. A vacuum dust-collection system is designed, CNC-routed and installed. A steel table is made to mount the table onto.

OpenRail attached to a 19" rackmount 15U box.

XDrive 3d printer, high quality large build volume.

This build is to show what's possible as well with openBuilds! I use a single ArduinoMega and 5 separate stepper drivers (A4988). The LEDs are all NeoPixels. Collision 'detection' is all done within the code, so the endstops are only sensors I use in this build. I'm a self-employed video-artist and this is my first installation which just needs power and it runs (where I'm quite proud of). Normally my interactive installations take a long setup time, so this installation is a relief :)

Big brother of the Charging Ox CNC machine.

A portable 3D Printer that can flat pack into a hard carry case

Open source 3D printer with very powerful heated bed and light weight x axis design. Full source repository can be found here: https://github.com/a-drizzle/Printer1

Hello ! This is my very first OpenBuilds build. It's based on the Maximus 3D Printer, published by mytechno3d : good source of inspiration !

This slider uses an 500mm OpenBuilds C-beam and the design is such that the effective length of the slider is slightly less then twice the length of the C-Beam. It can be used both motorized or not.

A CNC platform designed with swapable heads to do laser engraving/etching/cutting, routing and milling, as well as 3D printing.

Per the special notes its a variant of the C-Beam, Machine.... I have noticed that alot of people build a CNC router to cut parts for other larger CNC machines.. eg Delta Printers etc....plus this will enable me to cut parts for model RC plans UAV's etc...

A Rostock style delta bot with the parts which are typically 3D printed made from medium density fiberboard (MDF). It uses a home made hot end.

3d printed V-Slot Gantry Plate leveler.

This will be a DLP 3D Printer designed around an Openbuilds Frame and rail system. It will be a collaborated effort between myself and Ben Smith. We will be building two prototypes.

After expanding a Shapeoko 2 with the rails and motors left over, make yourself a laser engraver.

A 3D Scanning Station

In short...this was a fun project.

This build is intended as a light alternative to the Dremel rotary tool.

This is a Delta build using 1610 ballscrews from China

An all metal construction cartesian style 3D printer with a very rigid frame that has the flexibility to function as a desktop milling station or laser cutter with appropriate user designed attachments. Design is scaleable to suit any size requirement. All axis are leadscrew driven. V-Slot and Mini V-wheels have been utilised for the linear rails.

Document my OX build process. I will also be sharing SolidWorks parts files & assemblies.

Optical home and limit switches for cnc, 3D printers, laser cutters, etc.

This is a big 609 x 609 x 914 3d pritner with exchangable hot ends and extruders.

My first openbuilds submission, plain old c-beam machine. Seems like I've spent more time fighting the forum here redirecting in circles than actually building the machine. I'll try to add more pics if I ever find a path out of this corn maze...

Using a Raspberry Pi, Arduino and a Protoneer CNC Shield to create an Open Source CNC router controller. It will be equipped with a touch screen to control the on board processor. The touch screen will run a user interface that has buttons for added functionality. There will be a camera for monitoring progress from inside my office. The control box will also feature a way to power the vacuum and spindle/router . I will also be able to monitor room temp as well as Pi CPU temps and averages.

A Laut3k derivative that goes for volume and large number of print materials at the same time. Using OpenBuild linear motion systems to get away from belt drives.

An easy Epic Win for novice engineers new to the RepRap project www.3distributed.com

It took me 18 long nights to build it

Out with the Old in with the New. Trying to build a nice clean setup that myself and my sons can use and enjoy.

[EN] Build of my Multiple OX CNC. It's goal is to run in 2 differents modes : router and 3D printer modes. The router mode will allows the use of a laser diode or a standard spindle. [FR] Construction d'une CNC basée sur l'OX pour des usages multiples. Deux modes principaux sont prévus : l'impression 3D et l'usinage via une defonceuses. Le mode usinage permettra à l'avenir de placerune tête laser pour effectuer quelques gravures simples. Une version française : http://kermareg.be/?page_id=103

A simple 3D printed dust shoe for the cnc router. 2 parts held together with magnets for easy bit changes.

Tower Printer H-Belt type printer Prototype

The Ronin OX is a dedicated fiber composite milling machine. I give a complete in-depth article on how to take a nearly stock OX build and easily turn it into something that can mill carbon fiber and G10 plate effectively and quickly.

In this, the final part, I would like to introduce Machine Vision and show how it can be used, not only for tool position setting but also for resolving the triangle to calculate the G68 (local system rotated) for jobs which are not squarely placed on the work table.

This is my second Ox with a working area of 14" x 14" x 5" I wanted to build a small sturdy potable CNC router and this OxZilla has the nice upgrades !

Use of V-Slot for frame and rails with option to use identical 500mm uncut lengths: 8 * 20x60 x 500mm 8 * 20x40 x 500mm 7 * 20x20 x 500mm (2 cut into four identical 125mm pieces for filament holders) Use of uncut 500mm rails obtained through use of 12 joining plates for use as spacers. Alternate approach is to trim two 20x40 and 1 20x20 rail by 6-8mm each. Build volume ~400mm cubed (with dual extruders). Use of only openbuilds components! Currently in design phase...

This 3D Printer is made to provide the most accurate results with the least amount of investment. This Printer is being designed to allow the common user to own a very accurate piece of machinery.

This build is very straight forward. The design is simple. There is a great support community for Delta 3D printers.

A System of 3d printed parts to use along with your projects aluminum extrusion to cut your pieces of v-slot to length manually.

I am going to use this as a build log for my delta 3d printer build. I have access to a MakerBOT to print some of the parts. I am still finishing up a few of the design elements but the idea is to have a rigid unit to eliminate deflection in components and maintain accuracy.

This is a Chinese kit I got on ebay from someone in CA.

This is a Dual X-axis platform.

C-Beam Router using 1500mm lengths, 48x48" build area, and rack and pinion movement.

Leveling Platform / Stand 3D Printers

The STEAM Crane 3d printer uses the new C-Beam linear rail. It is being developed for an after school / summer camp program for kids. All of the electronics are housed in the base and the wiring is routed down the channels of the c-beam. This is done to contain as much of the loose wiring as possible, hopefully keeping it safer for kids.

A fully aluminium printer made from off the shelf components, no printed parts.

Mag arm deltabot with laser cut carriages and connectors.

Someone donated a E3D Volcano to me (http://e3d-online.com/Volcano/V6-VOLCANO-POWER-PACK-175-UNIVERSAL-24V) and with a super hotend like that, it feels like a waste to stick it into a small 3D printer. So I decided I want a 320x220mm (XY) machine, 200mm Z is plenty for me

Planning my build, just looking for design input at the moment. I definitely want a slave X axis. I am potentially going to go with one of the 1500W Chinese water cooled spindles.

An X-Y Stage created from two self contained acme screw linear actuators. This build was published as an example of how many of the OpenBuilds Parts can be used.

Another modification on the OX

Small Form factor based 3 axis Gantry style mill, Removeable mechanical module. Removable Electronics. with a removable machine pallet, for automation.

I have wanted a 3D printer for a while. I had thought to convert my ShapeOko machine to a 3D printer BUT after looking at having to replace the electronics with new and the small form factor. I went looking for a kit which would do what I want. Well I found it. It is the MakerFarm i3v printer.

Build the efficient and reliable all metal structure 3D Printer. Improved significantly with new concepts for printers. Great quality and up to 400 mm/s print speed (very fast). Built with heated bed, hybrid bowden suspended extruder, and counterweight (tested printing 21 hours straight with no motors hot). Optional smart controller for computerless printing. Print any kind of thermoplastic.

This is my 1st submission to openbuilds.com and my 1st venture into building a 3D Printer. The Phoenix 3d Printer is a kit from Ez3D, a company based out of Colorado, started and backed by successful Kick-starter and IndieGogo campaigns. The Phoenix 3d Printer kit is currently backlogged 10 to 12 weeks which means quite a wait. I will be chronicling my experience with this kit as I get it done.

LASER ENGRAVING DIY 60 WATT

Phlatprinter MKII Foam Cutting Machine

Creating a CNC mitre (45°) cutter, for picture frame cutting. Starting with an OX, but inverting various parts and adding a material table, with a stepper-controlled measuring guide.

This build is very straight forward. The design is simple. There is a great support community for Delta 3D printers.

Yet Another Openbuilds Router, my version :-)

Hell Yeah

This is the largest printer I have found. It is also the cheapest. The reason is that it is run by hand, without computer or motors or electronics. Put an object on one side and move the 3d pen while tracing the object. Move the z dimension by turning the crank on the lab jack to move the printed copy down a notch. Be creative!

Simple cartesian style CNC. Uses ACME screws for all 3 axes, 20x40 v-slots and should have 50cm x 50cm x 50cm work volume.

So in short this build is a work in progress; it aims to make a large 3d printer, medium size CNC mill and a small plasma cutter all in one CNC unit.

Planning my first build. Hope to achieve a larger format yet rigid design.

This is a work in progress 3D printer Dimensions are 230x230x340mm height. Print dimensions are: 135x135x160mm. Prototype has a bowden extruder with a J-head hotend. Assembly instructions: http://reprapstyle.blogspot.pt

Cartesian Printer, 200mm x 200mm x 380mm build area, enclosed, belt and pinion movement, heated bed, Raspberry Pi, Pi Cam, OctoPrint

Delta printer, Bed size 280 cm dimeter Print Height 300 cm not tested yet the speed

A new derivative of the famous OX CNC, with increases strength, rigidity, and accuracy.

A work in progress. working to refine the print head/carriage to integrate a bed level probe directly into the print head.

My first custom build, using vslot rails for Z and Y and 8mm rails for X. Currently printing parts for this using my Prusa I3. The build volume will be roughly 300mm^3, X and Y are belt driven with 8mm acme lead screws for Z. Will be uploading more info shortly as i continue to build the printer.

This is a basic description of my OX-like build of Babe, Paul Bunyan's Blue Ox. It is a work in progress. The idea has been germinating for about 4 years, with several twists and turns and false starts along the way.

A small, quiet and clean desktop CNC designed for fine cutting.

Proteus is the Greek God of change. Besides the numerous aspect of 3D printing that this could relate to this machine like the god can change. The Build allows for an interchanging head that will allow different functionality to be quickly and easily adapted. So you could print clay, silicon, plastic, cut with a laser cutter or even attach a rotary tool

My version of the popular Lautr3k 3D printer. UNI Panther colors of Purple and Yellow on black V-slot rails. 300x300 bed.

I creat a open source 3D Printer to print big things. Print size: 400x500x300 mm. You can download the Drawing in PDF and in Inventor 2013 format. The unwinding drawings are also included. I take some detail photos for a better understanding.

This is just a small project to get use to the OpenBuild products.

Rigid 3d printer with more than enough room for dual extruders. Easily expandable platform.

An OX build - little large than specs and plates 3D printed

A bigger OX. As this build is nothing new I will detail my build process, I am not an experienced builder, this will maybe help someone else. The size of the bOX will be 100cmx75cm. I will use aluminium plates, a tinyG, and most probably only open source / free software.

I am hoping to post a detailed build of my printer it is a large format using the RepRap RAMPS 1.4 & Mega 2560 & DRV8825 Driver + optical end stop +LCD 12864 -C 0.4mm Far-end Distal Dual-Head Nozzle Extruder Double Nozzle

This is a 1500 x 1500 Ox build

Custom build plate for 300mm x 300mm (12"x12"). The hole pattern is for the 20x60 V Slot

Building the full size OX.

A practical rotating and stand-alone spool holder which fits any filament extrusion 3D-printer. Several base files provided which make it fit different extruded aluminium profiles.

OpenBuilds box type printer using min-v-wheels for X & Y axis. Designed for plexiglas panel enclosure of build area.

Design of a multifunctional CNC machine.

Acquiring a CNC has been on my list for some time now. This concept is a bare bones, upgradeable machine that will not require a complete rebuild when new parts become available. With a cutting surface over 36" square, this beast should be capable of creating its own parts. Lowering the price to make upgrading and making this contraption beefier, faster, and more precise.

I've been working on commercial woodworking CNC's for year's under shop owner's that didn't want me to progress any further at a certain point. This is a project I've wanting to build for about 10 years now. I can't wait for the freedom to build what I know is possible without any negative input.

It is a first draw of my future Printer/CNC cutter.PCB mill Still need to work more on it

Berrybot inspired delta 3d printer with a few other tweaks and modifications.

OX MultiMachine

An USB Pendant for LinuxCNC / Mach3

Multi-tool 3D printer, laser cutter, and CNC mill.

For all other builders and robotic technies!