My OX cnc upgrade.

Overview of a 700mm x 1000mm machine based on the LEAD design and with the High Z mod from the start. Will have a parts list you can use to build yourself if you like the formfactor

Update a 20-year old bench top milling machine with OpenBuild Ecosystem electronics.

My goals for this build were to eliminate slop and flex while also allowing easy serviceability.

A simple build that helps you to mount the OpenBuilds Interface to the front of your machine.

Cheap Ballscrew Ox CNC Router.

Had left over parts from cnc plasma build.

A simple vacuum hold down/clamp set up using a 6hp canister vacuum.

Building a larger C-BEAM CNC Machine with no previous experience.

Very cheap CNC made from laser fired and bent parts.

Large 600mm x 350mm x 350mm Build Volume with lead screw driven motion. The printer build has a moving gantry and fixed heat bed. Open Source

Standard build with high Z using a Gauss probe instead of a router.

In progress CNC, (just design for the momment), I want to get some feedback about the design and the possible flexion of the aluminum profiles chosen

Ooznest OX CNC build

A small business idea led us here, lets see where it will go.

cnc made with a 6mm metal body .

I install the third extension on my cnc router and ask me, what can I do with a laser? So I make some test and find out - >>It is possible to engrave jeans clothes<<. Create your own Designer Jeans with a Laser!

Pick and place based on the Openbuilds ACRO 20x20

6 axis rig based on OpenBuild C-Beam and ESP32 MCU, WiFi controlled with custom app.

Machine with 12,5Nm closed loop steppers or servo steppers

The OpenBuilds Sphinx 55 - 500x500 Lead Screw Machine

Laser CNC made with mostly Openbuilds and amazon sourced components. Lots of 3d printed components as well. The main purpose is to cut EVA foam.

Major K40 Laser Mod

I have tested my Opt Lasers laser module on a "open" frame for some time. Decided that I want to test a corexy setup and combine it with a boxed/enclosed design - my goal is to get high precision + a safe setup with protection from the laser light + a fan to extract the smoke/exhaust..

Openbuilds Pick and Place using ideas from OpenPNP Frame work is from the Openbuilds Part store using 1000mm C beams and vslot 40x40 for support Surface is 3/4 " Particle board

Reworked PhlatPrinter Gen1 Adding dual nema 17s to all 3 axis Supprot for carriage to insure even dept cuts Lighting for view of cutting area

So Instead of buying a CNC Router which can cost thousands of dollars I ventured on the quest to design and build my own. I have multiple parts to this series. Hopefully all of my information I share helps!

An open source 3D printer design with a sturdy V-Slot frame

Heavy Duty build with 1605 Ballscrew and Linear Rail

Inspired by previous Sphinx builds by Sorin (w/ MGN Rails) and Kenneth's witthuhnCNC XKLBR-1S. I wanted to create a desktop unit that kept a minimal profile and neatly contained the PS, Controller, and all wiring, making it a singular unit that could be easily transportable (as it will be doing double duty at my home and at work)

I’m custom building a push table / cart for my cnc machines mostly out things I already had in my garage. Using a gray push utility cart as the main body and building around that.

Moveable Lead CNC1010 build with handles on four corners. Everything fits on one sheet of cut out 4x8 plywood

Improvements both real and suggested for the Workbee assembly

I will go over the attachments for the PP3 Z axis. soon. Before any thing else .You need to know the first PP3 ,used SKP 7 and Mach 3. Later on they used CNC USB.

Custom Z Axis for OptLaser 6watt and the Acro System

A strong desktop cnc router that will enable you to make larger aluminium plates without taking up to much room. Simple, strong and opensource ! Build one today..

This is my build for an ACRO system with a custom z-axis for changing z height for focusing or for adjusting depth when making multiple passes when cutting.

This is a upgrade to make a little deeper and a little bigger foot print for cutting. This is a copy of design off Rob Taylor idea for Dbl C Beam setup. The goal though is to design it around a new build with minimal tools for some one with no cnc access. Drillpress and drill bits and tap set. A 10in Non ferrous metal cutting blade for my table saw. Paper printer for printing DXF files.

My workbee build with some add ons

Building a printer that can fit inside and operate at ~200 C oven temperatures

This is a Sphinx variation, aimed to minimize footprint and maximize workarea. Work in progress.

Second better project, high durable mainframe, silent work, non vibration.

Here is my Project A CNC 3000 mm by 1500 mm, with a 2.2kW spindle collet ER25 and 4 stepper motor nema 23 425oz-in. The purpose being to have a large work surface for a minimum cost.

To build a simple EggBot

Attached to a scroll saw you can cut nested wooden spirals with this jig. Make two, three, four ... interlocking spirals that unwind/unscrew. Fascinating toys or art objects!

Ball screw drive, linear rail CNC Kit

Adding a rotary axis to the Workbee 1010. Including height modifications to the Workbee.

This OpenBuilds C-Beam XL actuator is the backbone of a lot of the awesome builds put together by the OpenBuilds community

Upgrade my 5 year old Makerfarm printer to use more V-Slot

Made with OpenBuilds 2020 and 2060 material/brackets/hardware. Simlabs wheel deck. Fanatec DD wheel base/wheel/pedals NRG seat Sim racing studio wind simulators Few 3D printed brackets/caps/cable holds

I am currently 15 years old, from Germany and trying to build a low budged CNC router. I only designed this CNC based on other CNC routers that I have seen and what I am able of. It consists mostly of 2.3cm plywood to keep costs down. The size of the work area is approx. 40 x 80 cm. I would be really glad if you could give me advice's for improvement on the design and everything else ... ( I could really need your help :) ) enjoy :)

Full aluminium profiles construction. Synrad 50w CO2 laser. Ruida controller. Yaskawa servo motors

This is my first CNC build. The Sea-OX is a machine built out of three 1000mm C-Beams. I plan to have a Y length of 1000mm and a X length of 650mm. The Z should have the ability to move approximately 100mm.

CNC laser with GRBL firmware on board

The crypt-cube is another project I've been working on off and on over the past year, unlike my previous built C3DO this is a much smaller built with a volume of 318mm x 240mm x 220mm. With this build my main focus is precision and speed.

DIY design and build of a roughing 2' by 3.5' CNC router

RF 100w laser cutter build, aluminium extrusion

It start out to be an upgrade of a CNC 3018-PRO but ended up being a full build

Create a ball screw carrier with out BF BK bearing blocks.

Belt drive linear scale for Mill and Lathe

Workbee 1010 with Duet controller from Ooznest

Yet another build of an improved C-Beam Machine, improving stiffness, size, versatility, and strength without increasing costs much.

This is a K-Cup sealer i constructed does a fine job

Large inexpensive build that can cut a 4x8 ft sheet with room to spare. Can be built using only a 3D printer and standard parts -- no special CNC'd plates required.

I found this to be a very fun exercise in building Bessy and will continue to improve her in the future.

This system allows you to adjust the position of the microphone remotely

Super Rigid CoreXY 3D Printer

This is a build for those of us that want to work fairly large but are in a tight space and budget

This build will use 1/2 inch copper water pipe as the primary material for all structural parts. As of now my intent is a cartesian design drawing from a few popular printers. I'm going to use the least amount of printed parts as possible and locally source as much as I can. I have built an EMT-conduit core-xy printer in the past and while it worked out fine, I feel copper is easier to work, manufactured with more precision, still reasonably inexpensive and will look super cool!

This project produced a movable framed canvas to cover a wall-mounted flat-screen TV when not being viewed, which at the touch of of a switch moves down below the TV and sound bar. The same switch is used afterwards to return the artwork up to cover the TV again. Photo shows mechanism without the canvas frame. See other photos.

A Cartesian printer using bushings for the Z axis instead of wheels or linear bearings. The design also synchronizes two Z axis screws with a timing belt for a level lift. The ratio of the drive pulley and Z axis pulleys produce .005 lift per full step on a 200 step motor, eliminating layer resolution "drift" caused by microstepping.

A small form factor machine in a soundproof enclosure

I have always wanted to work with CNC machinery...a few years back I got my chance to learn some basics at the Double Glazing Company where I was employed (very basic I might add) before the firm folded and I was made redundant...I wanted to continue learning and when I came across this site which push affordable machines I thought I'd give it a go. So I purchased a !000mmx750mm Screw Driven Workbee from Ooznest and I'm about to embark on my quest as many have done before me...Wish me Luck!

Below are the details of my build and a good story for those who read till the end. Sorry for the grammar

A proper CNC mill conversion. But quite small, with my trademark idiosyncracies.

Major rebuild of my Wanhao Duplicator i3 Plus.

WorkBee1510 with retractable space saving stand and customize build Marlin firmware and MarlinPanel (GCode Sender/UI)

It startet in May with some leftovers from a cnc router build. Now in the middle of December its 99% finish. Everything is lowcost, spend about 1600$ so far.

http://www.buildlog.net/sm_laser/drawings.html using this as a baseline.... Going to try and use all or most off the shelf parts.

This is the original C-Beam Sphinx with the 16 wheel X gantry plates. I'm using the Ethernet Smoothstepper, Gecko G540 stepper driver and Mach 4 for motion control.

This is a rework of a previous build I did on here, a mostly printed cartesian CNC. Initially intended to just be an update to that, but so many things changed including the linear motion and every single part has been modified significantly that I felt as though it deserved a whole new build.

This build is the documentation of someone with no experience building the OX cnc machine with a Gecko G540 controller and CNClinux

China Router frame with linear bolts, Nema23 and the icing on the cake “open build parts“

The Sphinx has all the components I need, except it will need a taller vertical lead screw, the same length as the horizontal ones. It will also need legs. So I need to start with the Sphinx parts list, then make a few changes.

Easy to build,low-cost, CoreXY

Inexpensive plasma table. Accurate, fast, and low maintenance.

A dual extrusion CoreXY printer with a 290 X 290mm build volume built entirely out of 2020 aluminum extrusion and using openbuilds mini-carriages for motion.

This is my first public build. Please be kind. We upgraded our C-Beam to the C-Cbeam X-Large. I want to give special thanks to Moag and the OpenBuilds team for making this happen.

Hobby project

Anti-Twist Design, larger lead screws, enhanced M8 wheel sets.

OX Based CNC

Heavy DIY plasma cutting table

Easy All-in-One Laser and Mounting Kit for your Openbuilds CNC.

The idea was to use materials from previuos failed projects into a succesful one. I have build this tiny but powerfull CNC machine mainly using the universal gantry plates for the X and Y axis. Also another innovative part is the fact that I assembled the Z gantry with 2 aluminum sections of 20X40 and one aluminum seccion of the 20X20. I used NEMA 17 stepper motors with GT2 pulleys. This was designed on Fusion360

A Heavy Duty version of the standard Big Ox build.

This is an Openbuilds LEAD 1510, modified to supports a liquid cooled 1.5Kw spindle. The movements are made with lead screw on all three axes.

This is a remix of Marshal Peck's Voxel OX, with some design tweaks inspired by Makerparts and jjcolletta. It has a build area of 300mm X 300mm X 480mm, but is easily configured for just about any build area up to 500mm X 500mm X 750mm. I have used some laser cut acrylic plates and a couple of 3D printed parts in its construction, however it can be assembled using nothing but OpenBuilds parts with the exception of the heated bed and the Y axis carrier for the heated bed.

Increase Z axis travel by 20-25mm with minimal modifications

This is my first build attempt, a large form (4x4ft.) 3 axis 4-motor CNC router table, . The build components are Baltic birch plywood, stepper motors, SBR linear bearings, and ball screws, LinuxCNC, Mesa controller.

Functional real-world 3D printer build with RM2-2RS bearings in routed V grooves on phenolic resin rails (lab countertop scraps) and NSK 25mm linear rails/trucks.