A strong desktop cnc router that will enable you to make larger aluminium plates without taking up to much room. Simple, strong and opensource ! Build one today..

It began with creating an extremely rigid axis that incorporates a multi C-Beam Linear Rail system as well as precision lead screws coupled with a tension system for the absolute maximum in performance.

The OpenBuilds WorkBee 1510 - 1500x1000 Belt Driven CNC Machine

Stronger frame for Prusa i3 MK2(s), MK2.5 and MK3 3D printer

This build uses drawer slides and thread rod to create foam wings and fuselages by passing a hot wire through the foam which makes very accurate shapes. I built a Radio Controlled SuperVC10 using foam but did have a cnc machine then so I had to make many templates to guide the hot wire. This inspired me to build a cnc hot wire cutter. Works really well and have made several RC models with it now

My machine is a combination of the Openbuilds Sphinx 55, MGN12 linear rails knockoffs and custom made plates made by Chris Laidlaw

The OpenBuilds Sphinx 55 - 500x500 Lead Screw Machine

5 X 5 Plasma table...Hypertherm 45 XP....CandCNC....Openbuilds

I have based this build on the OX build so I will not be going into too much detail of specefic assembly modules as they asre so well covered by Mark Carew already, but will go through the complete build on video. I will be addig additional tutorials on steppers and the other electronic parts as needed though as this project is sponsored by RS Components in the form of most of the Electronics and this is also the key focus of my YouTube channel www.youtube.com/c/thebreadboardca.

Project Completed.

This is going to be a Sphinx 1050 build. Starting off as a stock kit build using industrial electronics and opensource control software. Mods and upgrades to follow.

DIY build of a Co2 Laser cutter/engraver 12x24 working area.

2 watt Laser Engraver, Simple, Fairly Low Cost, and Portable

This build is very straight forward. The design is simple. There is a great support community for Delta 3D printers.

The OpenBuilds Sphinx 1050 - 500x1000 Lead Screw Machine

OX Based CNC

The OpenBuilds WorkBee 1050 - 1000x500 Lead Screw Driven CNC Machine

Stronger frame for Prusa i3 MK2 / MK2s / MK2.5 3D printer

A Sphinx build to inspire and encourage all those who want to get started with cnc to check out Opensbuilds line of machine bundles and hardware.

Some of the things that I have done to my 1510 Workbee Installed Linear rails and bearing blocks with drawings. Installed Ops console Made conversion plates for extruded aluminum to casters Extended z axis travel by a couple inches with steel plates. As of now in the process of installing Lead screws across the 1500mm length.

1000x1000mm Ballscrew driven OX Derivative. Dewalt 611 spindle and TB6600 Drivers.

This will showcase the build of my Rawcnc 1.5. A rigid cnc router from the Swedish company Rawcnc, featuring a rather cool linear motion system, rack & pinion and steel reinforced X-axis capable of milling aluminum.

The OpenBuilds Table Series offers a modular table structure that grows with your needs.

High Quality CoreXY with focus on quality and optimized printarea versus physical size of the printer.

laser mini 20 * 40 OPENBUILDS base frame.(크기 412x455mm) laser mini 20*40 기본프레임입니다. 기존 여러부품을 사용한 제품보다 부품수를 줄이면서 최소한의 단가를 뽑을려고 디자인했습니다.. 기존대비 부품수 절반에 단가도 절반을 줄이면서 최적의성능을 내려합니다.

We are a team representing private industry and public university all concerned about community. In the place i'm from we face problems related to prototyping industry, there's no accesibility to it, not because there is not machines to work with but the costs are really high if i want to make a single piece of any idea in order to develop a concept, our students get their degree but never were able to try any of the Hass or 3d systems machines available as it seems they need a PhD.

Shawn's adventure in assembling and customizing the Openbuild's version of the 1500x1000 Workbee.

I got lucky enough to purchase aluminum extrusions and linear motion components (and nuts/bolts/etc) at scrap metal prices when a bunch of industrial automation equipment was decommissioned. The only problem is that the aluminum extrusions are not metric sizes... they are the 1.5"x3" 80/20 series. It has presented a few challenges but nothing too bad.

This build is the documentation of someone with no experience building the OX cnc machine with a Gecko G540 controller and CNClinux

Building the full size OX.

A Rostock style delta bot with the parts which are typically 3D printed made from medium density fiberboard (MDF). It uses a home made hot end.

Bringing your lead screw precision and accuracy to new lengths using a simplistic tension system!

Upgraded 1500x1000 Ox cnc to 1605 Ballscrews on the Y axis. along with the J-tech laser to do most things.

I wanted a dust shoe that have a easy access to tool change and something that kind of float on the surface. And I have seen shoes with long brush that sucked in by the vacuum. I think I have the solution too all that here.

OpenBuilds C-beam 15mm belt on 1500mm C-Beam.

Attaching V Slot or mutable V Slot end on end to a larger steel frame table.

Large format CNC router with a 1500mm x 3000mm cutting envelope (5 x 10 ft) strong enough to cut wood and aluminum constructed from 20-series and 40-series aluminum extrusions. Complete Project Log w/ Pictures: https://goo.gl/photos/Co81AvGwVijE2zow9

This project shows how to use Openbuilds Vv slot extrusions and wheels to retrofit a Lulzbot Taz 4 or 5 printer. These modifications improve layer consistency, eliminate nozzle and bed sag, and allow for larger toolhead mounting. Project updates and newer accessory files may be located at http://www.thingiverse.com/piercet/designs

This is my first CNC router build, so I started with the OpenBuilds C-Beam Machine XLarge mechanical bundle, including four high torque stepper motors. I took my time with the mechanical build, sought and found some great help for my control system, and designed and built a custom cabinet to house everything.

The whole system is powered by 12V / DC power. Process it into Pellets or Granules to use it with your 3D Printer or Filament Extruder. Our self-developed steppermotor Controls allows you to optimally adjust Feedrate for your Situation. Forward, Backward and Stop is integrated for easy operation. The Speed can be continuously regulated via rotary switch.

C-Beam based CNC with Rack & Pinion (for the X Axis) and lead screws (for the Y Axis)

MiniMill with DW611 and SmoothieBoard 4x v1.1

This modified C-Beam, is a compact, powerful and affordable desktop CNC.

Large scale True 500x500x500 build volume 3D printer.

Working progress.

I am building a simple home brewed printer. I have a background in industrial automation so I figured how hard could this be. The mechanical build was pretty smooth as was the electrical side. Now just getting plastic out the hotend is my stopping point.

A CNC router designed to handle a 4'x8' sheet, for as close to $2000 as possible. The price barrier resulted in my choice to use timing belts rather than leadscrews or rack&pinion. Build List still being updated

ELECTRONICS - ARDUINO Mega 2560 + RAMPS 1.4 + power supply 12V - Leadshine DM 5042 external driver + Power supply 36V + NEMA 23 stepper motor SOFTWARE - Repetier Host to communicate with the Ramps - ARDUINO to upload the firmware (Marlin) MECANIC - V-Slots rails 40x40 + home-made plates - everything goes fine on the side of the build

build is in process the machine went together perfectly no issues at all but the software is another issue I have been trying to get the thing dialed in it is driving me nuts I'm still in the process will update if I ever get it figured out

Machined Aluminum MagBall Carriages

A proper CNC mill conversion. But quite small, with my trademark idiosyncracies.

Building of a big open frame laser engraver.

DIY design and build of a roughing 2' by 3.5' CNC router

A stock C-Beam with a CNC shield with DRV8825's

OX 1500mm x 1500mm w/1.5Kw Water Cooled Spindle & VFD ran by a Gecko G540 & Mach3

Z axes 1605 ballscrew, a comparative design proposal.

Yet Another Chinese Linear Rail CNC, my first one, doing this mainly for the fun of building it more than using it.

This is an Openbuilds LEAD 1510, modified to supports a liquid cooled 1.5Kw spindle. The movements are made with lead screw on all three axes.

A copy of the Stainless Ox by Martin Barfoed. Similar design, construction and control.

Ox inspired 1500 x 1500 CNC with belt and pinion drive and lead screw drive options.

A cartesian build with a build dimension of 200x200x750mm. I will be using a dual extruder, heated build plate, and a screw drive for the z axis.

First build of CNC OX for the purpose of using it for Guitar building to take a lot of the muscle work out so I can concentrate on the finer details.

I have been looking for a good solid kit to build off of for some time and when I saw the Ox buildlog I knew I had to have one. Ordered most of the pieces from Open Builds and started planning. Had a nice gentleman named Chris cut the required plates from 6061 aluminum for me (he sells them on eBay now if you're interested) and got to work.

I have re-purposed many of the parts from my Linear OX build. I'm using MGN 12 linear rails on all three axis, 5 start lead screws on the Z axis and I'm going to experiment with 5 start lead screw on the X axis. The frame plates are made from 1/8" laser cut mild steel, & open builds extrusion.

The Acro Laser Machine Build

classic router with a ab table

wooden parts of the enclosure can be removed easily used the existing extraction of my glass bead burners

I have been working on this project for something like 3 years on and off, sometimes leaving it for a few months. Now I really want to finish it. For me, the mechanical part was the easy (though long) part because I get to use about 17 CNC machines and MasterCAM and I am a machinist. The hard part is the electronics part. Had a few problems getting Windows to communicate to the X5 Mini via the USB cable but found something on the Smoothie forum and got the machine moving.

a 1000mm x 1500mm CBeam build with hgr20 hiwin rails 600w er16 spindle

My build is based on many different builds but pieced together into a unit specifically to suit my needs. The footprint, without motors, is around 500mm x 1000mm with a gantry height of around 250mm. I used a combination of C-Beam, for the linear transmission, and V-Slot for the base and gantry supports. Forged angle connectors were used for attachment and I utilized the C-Beam gantry cart kits with anti-backlash blocks for both Y axes, the X axis, and Z axis.

This build has been an educational experience. Software and hardware alike.

Sphinx 1050 kit mounted to a Husky 46" x 24.5" mobile workbench.

Started with a Rigidbot Big Added a single flat glass bed Used a Smoothieboard clone driving DRV8825

C-beam machine mods.

Wanna quet an nice looking device done by my hands

Inspired by previous Sphinx builds by Sorin (w/ MGN Rails) and Kenneth's witthuhnCNC XKLBR-1S. I wanted to create a desktop unit that kept a minimal profile and neatly contained the PS, Controller, and all wiring, making it a singular unit that could be easily transportable (as it will be doing double duty at my home and at work)

1500 x 1500 mm OpenBuild CNC

A plasma table able to cut 4'6" x 8'8" sheet. Low cost as possible.

This is the original C-Beam Sphinx with the 16 wheel X gantry plates. I'm using the Ethernet Smoothstepper, Gecko G540 stepper driver and Mach 4 for motion control.

Building the OB Lead 1515 was straight forward. The on-line OpenBuilds assembly videos were extremely clear and easy to follow. Initial build of this machine is with OpenBuilds BlackBox which simplified getting the electronics to work the first time. OpenBuilds staff are friendly and helpful.

Killerbee 1515 with modifications.

Two plus years in the making, I finally have a working ACRO 510 laser engraver system complete with enclosure and air filtration.

Video diary C-Beam XL build with massive steppers and a 1.5kW Chinese spindle.

Micro Ox Build

This is a Sphinx variation, aimed to minimize footprint and maximize workarea. Work in progress.

All metal frame 500mm bed Delta 3D printer

First build of a Lead 1515!

A Sphinx Linear rail build (600mm x 600mm) hence the title Sphinx66. Plates supplied by Chris Laidlaw. Linear rails used MGN15

I know this build is a little off category here at OB, but I wanted to share it with the community (as well as other coffee lovers) and show however vast the possibilities are when OB hardware is involved. This is a powered stand intended to operate a manual coffee grinder. It is compact, light, portable and uses simple drive components (B&D Cordless Screwdriver). I will post two version, V-1 (Beginner skill level ) and V-2 (Intermediate skill level). Both accomplish the same results.

In-progress 500x500x1800

This 1500mm tall Delta is a work in progress. The triangle corners are water jetted from 1" 6061 Aluminum, and are welded to 1" square tubing. The 1500mm OpenBuilds 20x20 V-Slot extrusions are held into the corner brackets by two stainless steel set screws per bracket. This printer will need to be reinforced with wall brackets due to the combination of height/materials.

This will be my first build ever! Looking forward to it , just gotta finish the new workshop first then I'm on it!

Xl 2 axis foam cutter Eps Surfboard blanks Simple open concept but high production machine. Shape 3d case with open builds controller

Theoretical Working area: 38" x 24" x 6" Actual Working Area: 31" x 23.6" x 4" Positioning Accuracy: about 0.01mm

A new design of my based on a couple different machines I have seen both on openbuilds and youtube. In the end will have a and X/Y workspace of 1250mm x 1000mm and a Z axis range of about 200mm.

Open build rovo 1000mm * 1000mm. (Rovo x ver) 20.06.2015 now in progress. rovo kit is the 10th product. 8th rovo 750,9 th rovo1000, 10th rovo x ver progress at the same time. 10th item is an aspect of 1000. It changes the size and z-axis has been up.

Custom black and red Big Ox

Build Notes: Here are all the parts necessary to re-produce this design. Please note, all of the parts are either sourced through openbuilds or have been selected and printed from thingiverse.

Getting more height out of the !510

C-Beam Router using 1500mm lengths, 48x48" build area, and rack and pinion movement.