i always make laser cutting machine, but when i see openbuilds, this can make more cheap gantry for make laser cutting.

Modded OX with full nema23 4 point support

The SMW3D OX, original other than a lot of learning!

Replacing the Pro Light control box with a Open Builds BlackBox.

My version of the popular Lautr3k 3D printer. UNI Panther colors of Purple and Yellow on black V-slot rails. 300x300 bed.

A simple low cost rotomolder.

A home-made CNC-machine with a 1.5 kW air cooled spindle motor suitable for milling materials such as wood, plastic and soft metals. The work table is 650 mm wide by 700 mm deep and the maximum movement is set to 560 mm for the x-axis, 480 mm for the y-axis and 105 mm for the z-axis.

C-beam machine mods.

Hello all, wanted to share my custom build that I planed to do. My idea was to drill foam blocks to make molds for my projects. The CNC will be 1500-1500mm with a higher Z-Axis. So I redesigned the Gantry Plates that will be cut out at some other place. I hope you can share your opinion on my project.

A Rigid Delta Printer using C-Beam screw actuators

So this is my custom 40W build. I wanted to make another laser similar to the one I built but a lot smaller and an all in one system so that if I ever decide to do a farmers market or something similar, I wanted to be able to put the laser on the back of the car and drive to whatever location. I think it's going to work. It will be see-through with lights and screens eveywhere. The lights alone should attract people like flies. That's the plan anyway.

While i achieved the desired taler Z axis this was very notable of the cost of the stiffness of the Y axis - the Y axis is now quite wobbly. i do not recommend such a big Z axis on a OX CNC machine where the requirement is a good precision.

IIOT WiFi Plasma CNC.

CNC laser with GRBL firmware on board

Mini Additive Manufacturing Printer by Chris Scholl

Tough 3D Printer using OpenBuilds Parts!

The new C-Beam kit expanded to 1000mm . extra support built in for the extents of the travel.

This build is based on the C-Beam build by Mark Carew. I have added axis limit switches and a remote mounted control cabinet. This build also uses a custom moveable table.

Simple steel tube design Plasma water table

Square shaped OX for doing general purpose engraving and cutting into wood, acrylic, and aluminum.

Sphinx 1050 kit mounted to a Husky 46" x 24.5" mobile workbench.

Watercooled 3D printer

Cheap chinese K40 laser upgrades, including 60x30cm working area, MKS or SKR controllerboard (smoothieware or marlin, not yet decided.) Light, psu and a bit more :)

Berrybot inspired delta 3d printer with a few other tweaks and modifications.

XDrive 3d printer, high quality large build volume.

Custom build, after building the prusa i3 and upgrading to i3v, I wanted to build something more sturdy that can print fast and more accurate. Model is built in Fusion 360

Portable, high-speed, low-cost advanced multi-tool desktop factory derived from LulzBot Taz and TazMega.

This Build Is Is Inspired By OOZ Nest CNC, But With Some Changes,

Started with a Rigidbot Big Added a single flat glass bed Used a Smoothieboard clone driving DRV8825

1M C-beam xy variant

Super solid core xy build inspired by the e3d tool changer

OX CNC built using the kit from SMW3D with a Smoothieboard 5 and external motor drivers.

How to modularize the 3D Systems Cube 3 extruder nozzle.

Fully welded, fixed gantry CNC router, with chinese linear motion parts, in progress

Wanna quet an nice looking device done by my hands

Killerbee 1515 with modifications.

The goal is to have a relatively strong CNC to be able to cut alu. Working space will be around 800x350x100mm.

Very stout 2'x4' machine with a deep Z axis

A plasma table able to cut 4'6" x 8'8" sheet. Low cost as possible.

Major rebuild of my Wanhao Duplicator i3 Plus.

This is an automatic cocktail mixer made with 8 small peristaltic pumps. this is driven with the touch screen or over wifi. the controller used is a raspberry pi with a Apache webserver

Building the OB Lead 1515 was straight forward. The on-line OpenBuilds assembly videos were extremely clear and easy to follow. Initial build of this machine is with OpenBuilds BlackBox which simplified getting the electronics to work the first time. OpenBuilds staff are friendly and helpful.

My first printer! I went for a simple cartesian design, based on evilc66 one. It uses 1000 mm C-beam linear actuators. The build volume is 700x700x700 mm^3.

This is the original C-Beam Sphinx with the 16 wheel X gantry plates. I'm using the Ethernet Smoothstepper, Gecko G540 stepper driver and Mach 4 for motion control.

A quick and easy way to make a 3-way mitered corner using Corner Connectors

T-slot, v-slot, aluminum angle make up the majority of the structure.

Aluminum-framed enclosure for TAZ 6 3d Printer made with Makerlink.

I have tested my Opt Lasers laser module on a "open" frame for some time. Decided that I want to test a corexy setup and combine it with a boxed/enclosed design - my goal is to get high precision + a safe setup with protection from the laser light + a fan to extract the smoke/exhaust..

Small CNC - made with some custom lasercut+bent sheetmetal parts + Openbuilds V Slot

CNC MILLING ROUTER

Video diary C-Beam XL build with massive steppers and a 1.5kW Chinese spindle.

Getting an accurate scan of a golf ball can be difficult with general-purpose 3D scanners. This purpose-built golf ball scanner uses a very accurate Keyence LK-081 laser displacement sensor with an Open Builds linear actuator for the vertical axis and a Sherline CNC rotary table for the turntable. Scan detail is determined by the sample step size and can be set arbitrarily based on desired scan time.

OpenBuilds CNC 500x500

Theoretical Working Area: 360x360x75mm Actual Working Area: 300x300x75mm Will Update Later

A Sphinx Linear rail build (600mm x 600mm) hence the title Sphinx66. Plates supplied by Chris Laidlaw. Linear rails used MGN15

Lord willing I will be showing you how build a robust and easy to build 3D printer framework using V-Slot rails and rollers. It's a little bulky, but it has all spring tensioned rollers on all axes, and can be built entirely without custom machining on any parts. You will need digital calipers, a drill press, a carbide toothed miter saw for cutting aluminum extrusions, and lots of little screws!

I have always wanted to work with CNC machinery...a few years back I got my chance to learn some basics at the Double Glazing Company where I was employed (very basic I might add) before the firm folded and I was made redundant...I wanted to continue learning and when I came across this site which push affordable machines I thought I'd give it a go. So I purchased a !000mmx750mm Screw Driven Workbee from Ooznest and I'm about to embark on my quest as many have done before me...Wish me Luck!

A small build using some small vslot scrap piece which shows the versatlity of the v-slot system

Create a ball screw carrier with out BF BK bearing blocks.

A stout 3D printer build with the hopes of being able to serve as a light mill (PCB) and laser engraver

Not much to say... Soundproofing box for noisy works... Build in MDF and 20 mm plexiglas. Very effective!!!

This is a cnc router with 3 axis and a kress 1050 motor. Its 140x120cm and a homebuild with your help!

just wanted to share my build of a huge 3d printer. It stands just over 2 meters tall and has a total print area of around 850mm x 850mm.

The 3D printer will be able to print 2x2x2m components and not just in PLA or ABS. It's not just a DIY printer but I'm trying to apply engineering formulas to make it. I'm going to apply the state of art for 3D printing and scannering existing.

This is my interpretation of the OB Minimill, what I've changed so far, and what may continue to change as my requirements change.

Here is the consolidation of my woodworking shop, a CNC Router!

Simple enclosure for the OB Minimill

This is a small desktop CNC inspired by the Mini OX project. It's designed with the nema 17 motors in mind. It's a 650mm x 500mm machine that it will be used to mill cast acrlic.

Two plus years in the making, I finally have a working ACRO 510 laser engraver system complete with enclosure and air filtration.

Micro Ox Build

First build of a Lead 1515!

This project is focused on developing a low-cost, portable and open-source FDM 3D Printer.

This Project is meant to teach introductory robotics and arduino styled micro-controllers to HS and MS students.

Hell Yeah

I will write a short buildlog here with mostly pictures. I designed this lasercutter in solidworks(not totally finished) for a good overview and such that the steel tubes could be lasercut by a company, the metal frame is based on the lasercutter the KÄSER, which you can find on cnczone.nl. The mechical parts are designed by myself because I had no mill to my use, so the mechnical parts are lasercut(same company as tube) steelplates welded together.

A small router for thin plate stock

Roberta Clementine's first daughter printer Alice Clementine!

Open source 3D printer with very powerful heated bed and light weight x axis design. Full source repository can be found here: https://github.com/a-drizzle/Printer1

This is my build for an ACRO system with a custom z-axis for changing z height for focusing or for adjusting depth when making multiple passes when cutting.

The first criteria was portability, the second was cutting out a sheet of ply, the third was the ability to shape a foam surfboard blank, but the main criteria was a small budget.

Stabilus 3d Large Format Printer Kit

This is a Sphinx variation, aimed to minimize footprint and maximize workarea. Work in progress.

All metal frame 500mm bed Delta 3D printer

This is the largest printer I have found. It is also the cheapest. The reason is that it is run by hand, without computer or motors or electronics. Put an object on one side and move the 3d pen while tracing the object. Move the z dimension by turning the crank on the lab jack to move the printed copy down a notch. Be creative!

Increase Z axis travel by 20-25mm with minimal modifications

A Rod-type Linear Actuator based on the 40x40 V-slot profile

I know this build is a little off category here at OB, but I wanted to share it with the community (as well as other coffee lovers) and show however vast the possibilities are when OB hardware is involved. This is a powered stand intended to operate a manual coffee grinder. It is compact, light, portable and uses simple drive components (B&D Cordless Screwdriver). I will post two version, V-1 (Beginner skill level ) and V-2 (Intermediate skill level). Both accomplish the same results.

I've been working on commercial woodworking CNC's for year's under shop owner's that didn't want me to progress any further at a certain point. This is a project I've wanting to build for about 10 years now. I can't wait for the freedom to build what I know is possible without any negative input.

My First major improvement was changing the controller to a Acorn board. I loved the way a dedicated userinterface was speeding up my workflow. Next project my Y Axis. On Aliexpress I ordered a couple of 16mm ballscrews and some lineair rail. Before I took my gantry off I quickly made some aluminium profiles to fit my carriages. Withouth any doubt these improvements where worth it

My goals for this build were to eliminate slop and flex while also allowing easy serviceability.

A modified 1000x1000 Sphinx, with a built in vaccum table.

I built a motion control camera slider with the V-Slot® NEMA 17 Linear Actuator Bundle (Belt Driven)

A framing design for cantilever style printers

This is a major redesign to the Z-axis of an otherwise stock Shapeoko 2.

Just starting a miter saw stop system. Any suggestions appreciated.

Created a small Z axis for the ACRO motion system. I wanted to more easily adjust the height of the laser to accommodate various thicknesses of material, without having to manually loosen screws to adjust. Also wanted to be able to vary the height for multiple cutting passes on some materials. Try to stick to a similar aesthetic as the original ACRO system and plates.

This is based on core XY kinematics. First of all, we designed a CAD model. Most of the required parts are designed by us in solidworks software, and some parts are downloaded from a web platform ‘grabcad’. After that we assembled those parts and inspected them in solidworks. The designed CAD models are frame of 470mmX392mmX545mm SBR linear guide rod, linear guide holder, lead screw, motor mounts, pulley, bed mount, idler block, timing belt clamper.

This is a modification I made to my Voxel Ox 3D Printer Z axis, which synchronizes the Z leadscrews via a shaft and helical gear transmission. It prevents the two Z leadscrew from getting out of adjustment relative to each other, and uses a single Z motor instead of two. This build is just documenting the specific changes I have made to the Z-axis, since the frame and other axes are still from the original Voxel Ox design.

An OX Router I'd like to modify to improve the frame rigidity and resolve some alignment problems

v-slot linear actuator build.