20x26x28 inch Build Volume CoreXY. Unlike many builds, I've decoupled the XY movements from the Z-Axis lead screws to help prevent Wobble, will be using linear guide rails, and mains powered bed heater, and a bed that is Allowed to thermally grow. This build is JUST narrow enough to fit through a standard sized doorway.

A simple but elegent couch legs

This is a totally original build of an od id grinder and thread grinder, I hope.

Simple upgrade of the Y axis on a Cbeam sphinx from 500mm to 1000mm.

A posi-drive leveling printer in 300x300x380mm format that easily breaks down for suitcase size shipping.

Getting an accurate scan of a golf ball can be difficult with general-purpose 3D scanners. This purpose-built golf ball scanner uses a very accurate Keyence LK-081 laser displacement sensor with an Open Builds linear actuator for the vertical axis and a Sherline CNC rotary table for the turntable. Scan detail is determined by the sample step size and can be set arbitrarily based on desired scan time.

Simple cnc with 5mm steel plates.

This is my first build attempt, a large form (4x4ft.) 3 axis 4-motor CNC router table, . The build components are Baltic birch plywood, stepper motors, SBR linear bearings, and ball screws, LinuxCNC, Mesa controller.

A 200mm x 300mm x 200mm workhorse that never needs leveling due to Posi-Drive Leveling design.

I used the cad designs for the c beam to find a solution to my initial sourcing problem. I figured that I could use 2x 20x20 and 1x 20x80 Profil to create a c beam actuator. I sourced all of the profiles from a local machin builder and t-nuts and screws in my local hardware store. Some parts are currently in 3d printed pla for testing reasons.

Senior Design Project Bennett Robertson, Megan England University of Iowa College of Engineering

At the moment this build is in progress, I will be updating the files as I finish the remainder of the machine. This machine is intended to be a multipurpose CNC, but a bit bigger than a desktop unit. The machine is scalable in the X and Y axis.

This is a fully adjustable, low profile rotary axis for your Laser Cutter. Many OpenBuilds components are used, plus a handful of 3D printed parts.

Made with OpenBuilds 2020 and 2060 material/brackets/hardware. Simlabs wheel deck. Fanatec DD wheel base/wheel/pedals NRG seat Sim racing studio wind simulators Few 3D printed brackets/caps/cable holds

C-beam machine mods.

Two plus years in the making, I finally have a working ACRO 510 laser engraver system complete with enclosure and air filtration.

This is a rework of a previous build I did on here, a mostly printed cartesian CNC. Initially intended to just be an update to that, but so many things changed including the linear motion and every single part has been modified significantly that I felt as though it deserved a whole new build.

This will be my second CNC build but this time a proper CNC not a small desktop model that I played with for a while to learn Gcode, It was great but now its time to start playing with the big boys and girls.

I know this build is a little off category here at OB, but I wanted to share it with the community (as well as other coffee lovers) and show however vast the possibilities are when OB hardware is involved. This is a powered stand intended to operate a manual coffee grinder. It is compact, light, portable and uses simple drive components (B&D Cordless Screwdriver). I will post two version, V-1 (Beginner skill level ) and V-2 (Intermediate skill level). Both accomplish the same results.

A 1000 by 1000 CNC Router with linear rails and a control box.

How to build an Independent Dual EXtruder (IDEX) 3D printer from OpenBuilds parts.

Super solid core xy build inspired by the e3d tool changer

DIY design and build of a roughing 2' by 3.5' CNC router

How to convert an angle grinder into an electric drill? Remove the angle grinder, leaving only one main motor, and then find a suitable intermediate roller with a point drill to assemble it.

A C-Beam machine design, strengthened with extra brackets and plates. GRBL controlled, opto-isolated inputs, jogging box.

Get organized with the SharkBits Holder!

Built a 32"x40" ACRO Kit for my 10watt Endurance Laser. Put it in a stand alone clamshell cabinet, added a 340cfm 6" fan and variable speed switch for the fan. Using LIght Burn for my primary software. It seems to be work well.

Getting more height out of the !510

This is a lead 1010 build that I wanted to have a little fun with. I purchased the whole Lead 1010 kit, and felt like studying a few shortcomings of the original to see if I can improve it or just have some fun with it.

I Like the Sphinx design thought I would attempt my first build. I wanted to build this and use Arduino controller with GRBL to be able to learn and understand my machine.

My goals for this build were to eliminate slop and flex while also allowing easy serviceability.

A sun cutter only using mirror and glass balls with x and y table movement

2 days to build Up and running some EMI issues but I think I have them resolved Big shoutout to the community

The Microwave Filter Tuner (MFT) combined with the University of Regina’s tuning algorithm automatically tunes microwave filters by using a custom CNC machine with a computer vision system for identifying, mapping, and tuning each filter element, providing improved consistency, flexibility, and accuracy compared to traditional methods. The MFT is low cost and is capable of tuning multiple filter configurations with minimal preparation.

Z-Axis upgrade with linear rails, SFU1204 Ball Screw and full aluminium construction.

Modular and Scalable CoreXY Printer with all metal parts.

In progress CNC, (just design for the momment), I want to get some feedback about the design and the possible flexion of the aluminum profiles chosen

The goal for this bot is to lay down mustard on sausages and burger patties in a smooth and sexy way that looks good for the camera.

I made a 5x10 foot cnc out of the parts I bought on this site. It's been upgraded and tinkered with ever since. The end goal is to learn enough to learn to build a large 10x10 foot 3d printer.

V-SLOT profiles and OpenBuilds accessories give us many possibilities. We decided to build a manual ROUTER SLED using only components of the OpenBuilds system. The design is simple to build, construction takes little time, and the frame is easy to transport.

Bringing your lead screw precision and accuracy to new lengths using a simplistic tension system!

PeeNaPle_V1.4b is a BoB controller board for 3D Printers, CnC and cartesian machine, using the latest Teensy_4.1

Stabilus 3d Large Format Printer Kit

Large Format CO2 Laser Cutter

The OpenBuilds Table Series offers a modular table structure that grows with your needs.

Anti-Twist Design, larger lead screws, enhanced M8 wheel sets.

The idea was to use materials from previuos failed projects into a succesful one. I have build this tiny but powerfull CNC machine mainly using the universal gantry plates for the X and Y axis. Also another innovative part is the fact that I assembled the Z gantry with 2 aluminum sections of 20X40 and one aluminum seccion of the 20X20. I used NEMA 17 stepper motors with GT2 pulleys. This was designed on Fusion360

Simple Swing Arm Build for the Modular Table Series. Create a simple vacuum swing arm that swings over your machine keeping your vacuum hose and router cord, etc. up and out of the way

A simple build that helps you to mount the OpenBuilds Interface to the front of your machine.

A custom Delta printer for large projects with any filament that still retains speed and accuracy, all within a 15 amp/110VAC power budget. Based on Johann's Mini Kossel design.

Progetto di un laser CO2 da 50w Autocostruito, con scheda di controllo MKS Sbase v.1.3 Firmware Smoothieware versione CNC Struttura realizzata con profili T-slot 20x20 e 20x40

It start out to be an upgrade of a CNC 3018-PRO but ended up being a full build

CNC laser with GRBL firmware on board

Ball screw drive, linear rail CNC Kit

Attached to a scroll saw you can cut nested wooden spirals with this jig. Make two, three, four ... interlocking spirals that unwind/unscrew. Fascinating toys or art objects!

Building a printer that can fit inside and operate at ~200 C oven temperatures

This is my build for an ACRO system with a custom z-axis for changing z height for focusing or for adjusting depth when making multiple passes when cutting.

Replacing the Pro Light control box with a Open Builds BlackBox.

Moveable Lead CNC1010 build with handles on four corners. Everything fits on one sheet of cut out 4x8 plywood

Used Laguna Swift 4X4 CNC mill with Water-cooled Spindle and RichAuto serial pendant retrofitted with OpenBuilds/Blackbox/Interface

I have tested my Opt Lasers laser module on a "open" frame for some time. Decided that I want to test a corexy setup and combine it with a boxed/enclosed design - my goal is to get high precision + a safe setup with protection from the laser light + a fan to extract the smoke/exhaust..

Standard build with high Z using a Gauss probe instead of a router.

Very cheap CNC made from laser fired and bent parts.

Build of a small laser engraver using V-slot profiles and 3d printed parts

Another Cartesian style build with parts from the UK, US & China.

A cabinet to keep a constant temperature for pizza or bread mother dough to grow.

Update a 20-year old bench top milling machine with OpenBuild Ecosystem electronics.

GHOST Case build for the OpenBuilds Black Box Motion Control System

Cheap chinese K40 laser upgrades, including 60x30cm working area, MKS or SKR controllerboard (smoothieware or marlin, not yet decided.) Light, psu and a bit more :)

I decided to start designing this printer, this will be my solution for a more rugged printer that you can use as workhorses...

A six axis camera slider with a 7th LIFT axis added!

First build of a Lead 1515!

Build using standard parts as much as possible, Open Builds etc. To keep printer usable for more materials will be trying a heated bed with rotary elec union for the thermistor and power.

Rubber company use as a lathe cutter for accurate cuts compared to hand cutting.

I made this from A to Z at home by myself with reading and watching tones of videos. 50 cm X 50 cm but I get 40cm x 35 cm as a real workread

lead machine plasma table with Black Box, and Torch Height Control

1500*1500*1900 (xyz) Biocomposite Pellet 3D printer

my first cnc build using the lead 1010 to build bigger and better!!

I built the lathe as a dedicated rotary axis, but I soon realized I could have a back up CNC for very little expense.

A clone of https://openbuilds.com/builds/dedicated-compact-rotary-axis-laser-engraver.10204/

Fixed Gantry CNC with good accuracy and rigidity but for a higher price than the usual CNC's on the site.

OLD Lead 1010 High Z Mod converted to Newest Lead 1515 with High Z mod, slimmer cbeam motor mounts, thrust bearings etc. Extended by original table out and upgraded my 1.5kw VFD and Spindle to 4kw ER20 Spindle and 7.5kw GT VFD

i would like to build a sturdy motorized photographic copy stand. i have hobbled together a hand crank version using a used umbrella pole but it is not suitable as it is awkward and wobbly.

A Sphinx Linear rail build (600mm x 600mm) hence the title Sphinx66. Plates supplied by Chris Laidlaw. Linear rails used MGN15

An ACRO laser put together with some repurposed and some new parts.

CNC Glass cutter

This is based on core XY kinematics. First of all, we designed a CAD model. Most of the required parts are designed by us in solidworks software, and some parts are downloaded from a web platform ‘grabcad’. After that we assembled those parts and inspected them in solidworks. The designed CAD models are frame of 470mmX392mmX545mm SBR linear guide rod, linear guide holder, lead screw, motor mounts, pulley, bed mount, idler block, timing belt clamper.

CNC SPINDLE FOR DIY ROUTERS AND MILLING MACHINES ITSRS-985 MOTOR HAS MUCH BEFINITS THAN ANY OTHER DC MOTOR IN MARKET

Replacing the Electronics and Spindle. Intending to rewire all the buttons and make it into a more modern and easy to use CNC.

Belt driven 3-axis linear system for high precision and low costs. > Threading and linear real cutting needed

It's a Z floating head idea. Works well. Recommend cleaning the inside of your holes well with Q tips, and polishing the 1/4-20 bolts with car wax and you won't need oil as it slides perfectly. Hope this helps

Hello. I build this 600 by 600 printer and hope to share it. I plan to sell custom builds with my website in the middle of this yeahr while making all parts accesibble online for replacements and own builds. My plan was to build a better and more accessible big volume 3d-printer as cheap as possible. I got some inspiration of the ender creality 3, the crazy-Print xyz 300 and the veho 600 tronxy which was simply not relaible and satisfying overal.

Not sure if the Blackbox X32 is the right option here, just looking for guidance.

long overdue overhaul of 1000 x 1000 machine

This is a story about a guy who started with a $25 set of plans, and through 4 iterations/ rebuilds, ended up with a professional quality CNC plasma table capable of cutting anything steel up to 2 inches thick.

Automated Media blaster retrofit.

F-Ender-Plus its based on the Ender 3 Pro, but improved: CR-10 hotend, double gear extruder, double z-axis motor, bltouch incorporated, hotbed leveling improved strings kit. Most made using local vendor parts, and still I'm increasing my knowledge of how get better 3D printings by calibrating motors steps, leveling the hotbed and z-axis; using a 3mm thick glass...

Turning my prototypes into real objects, it will be required a great amount of drawings, A LOT. Therefore, against the ink costs raise price push me to think in a way to draw models, blueprints, etc. at very, VERY low cost. This is where my DrawBot was born